demoboy333
Feature Winner
Enter your message here...
Posts: 3,129
|
Post by demoboy333 on Jul 12, 2021 20:56:35 GMT -5
|
|
Hotfoot674
Heat Winner
If you're headers aren't cherry red by the end of the night then you didn't try/hit hard enough,
Posts: 330
|
Post by Hotfoot674 on Jul 13, 2021 14:42:31 GMT -5
^^^^^^^ nice shifter, replace the ball with a small piston.
|
|
demoboy333
Feature Winner
Enter your message here...
Posts: 3,129
|
Post by demoboy333 on Jul 13, 2021 20:55:11 GMT -5
^^^^^^^ nice shifter, replace the ball with a small piston. Won't be a piston but will change it in time. Trying to get this done in time to run it. |
|
|
|
Post by smashincwa on Jul 14, 2021 8:51:24 GMT -5
If you dont have a distributor protector, you'll need to cut more firewall out higher up and back. I'd just cut the whole thing out and put a strong cross brace on attached to the roof bars.
|
|
demoboy333
Feature Winner
Enter your message here...
Posts: 3,129
|
Post by demoboy333 on Jul 14, 2021 10:56:27 GMT -5
If you dont have a distributor protector, you'll need to cut more firewall out higher up and back. I'd just cut the whole thing out and put a strong cross brace on attached to the roof bars. Normally didn't have to cut it all out but planned to cut more once I sit in the engine. But was looking at cross braces to help the spring of firewall. |
|
|
|
Post by roughneck06 on Jul 16, 2021 7:53:13 GMT -5
Did u weld your bumper on before setting ride height? Curious why u didn't put your plate over the holes on the pass rail where they all bend? Jw is all.
|
|
demoboy333
Feature Winner
Enter your message here...
Posts: 3,129
|
Post by demoboy333 on Jul 16, 2021 20:04:47 GMT -5
Did u weld your bumper on before setting ride height? Curious why u didn't put your plate over the holes on the pass rail where they all bend? Jw is all. I did max out my height before only allowed 2x2 straps 2 straps per a arm. Im sitting at 27 inchs to top of bumper. My plate was only allowed 14 inch by 4 inch so thats why I didn't cover the lower holes. Besides that the partial slotted hole is left but as the car bends it will get more plates only allowed 4 plates besides the bumper bracket till it bends. |
|
|
|
demoboy333
Feature Winner
Enter your message here...
Posts: 3,129
|
Post by demoboy333 on Jul 20, 2021 22:04:31 GMT -5
Coming down to crunch time. Down to drive line and front clip. Front clip is prepped so its fast. But derby is this week. So pics will get uploaded later as I have extra time. Had to rebuild a engine.... Pedals is mounted Steering column is bolted and mounted Engine is built ready to drop in Front clip is ready to be welded on.     |
|
demoboy333
Feature Winner
Enter your message here...
Posts: 3,129
|
Post by demoboy333 on Jul 22, 2021 21:08:09 GMT -5
Update. Engine and trans are in and bolted down. Front clip is on and all thread ran and bolted into place. Drive shaft is in. Fuel lines and tranny lines hooked up. Shifter adjusted. Few things still to do before paint but should get painted by night fall tomorrow
|
|
demoboy333
Feature Winner
Enter your message here...
Posts: 3,129
|
Post by demoboy333 on Jul 24, 2021 1:27:06 GMT -5
|
|
|
|
Post by smashincwa on Jul 24, 2021 10:34:08 GMT -5
looks competitive!
|
|
owen11x
Feature Winner
Ford makes it, Chevy shakes it, Mopar breaks it!
Posts: 2,636
|
Post by owen11x on Jul 24, 2021 12:28:41 GMT -5
Aside from front bumper which is only 1 year different than the fury bumpers I run that wagon is almost a T to the few I've built
|
|
demoboy333
Feature Winner
Enter your message here...
Posts: 3,129
|
Post by demoboy333 on Jul 24, 2021 15:46:03 GMT -5
 headed ou to my county fair show. Same show I took the shocker to. |
|
demoboy333
Feature Winner
Enter your message here...
Posts: 3,129
|
Post by demoboy333 on Jul 25, 2021 0:44:02 GMT -5
|
|
few pics as it got finished up over pass couple days. Got a paint job at midnight will add color tomorrow. 
