snake
Heat Winner
Posts: 368
|
Post by snake on May 1, 2018 9:01:55 GMT -5
add 5"
|
|
snake
Heat Winner
Posts: 368
|
Post by snake on Apr 14, 2018 16:27:28 GMT -5
Might run it just to take one guy out at a icons show
|
|
snake
Heat Winner
Posts: 368
|
Post by snake on Jan 20, 2018 20:48:47 GMT -5
sleeve it and mount it, bottom bolt is welded bottom of frame
|
|
snake
Heat Winner
Posts: 368
|
Post by snake on Jan 17, 2018 20:48:59 GMT -5
|
|
snake
Heat Winner
Posts: 368
|
Post by snake on Jan 9, 2018 19:44:25 GMT -5
No the bolt pattern is different. C clip is striaght, bolt in axles are canted. thanks, so you know where I could find new ones? Some how mine must of got threw in the scrap pile while it was apart Yes part number would be nice for new bia backing plates , cannot find part number either . planning maybe switch to disk instead of drum with a 90s swap with bracket re indexed
|
|
snake
Heat Winner
Posts: 368
|
Post by snake on Jan 8, 2018 19:30:07 GMT -5
gm bia on a 03 vic
|
|
snake
Heat Winner
Posts: 368
|
Post by snake on Jan 6, 2018 18:59:13 GMT -5
|
|
snake
Heat Winner
Posts: 368
|
Post by snake on Nov 14, 2017 21:47:17 GMT -5
Same Same Was wishful things were going to change
add these to 2019
03&up 2003 and up will follow all the rules listed here and all rules listed below as well. You have 2 options
option 1 -You can weld in a cradle from a 79-02 vic, marquis, etc. with the same configuration that it came with from the factory onto your 2003 & up frame. MAX weld bead is 3/8" wide and no added metal. -The cradle and suspension components must be welded within 2" of factory location. *measure from crush box bolt holes forward on both models. -You may tilt them in one location only
-you may have a factory spring pocket welded on the frame for your ball joint protector or a piece of square tube like listed above. (Spring pocket section CAN NOT BE WIDER THAN A-ARM)
-NO shortening the frame on 2003 & up -NO filling the crush point holes
Option 2 - you may run a bolt in style cradle - the cradle must not add any strength to the front frame beyond what the factory 79-02 cradle would in factory configuration. -No welding on the frame to cradle at all -utilize the factory bolting locations -cradle and all suspension components must mount within 2" of factory location -NO shortening the frame on 2003 & up -NO filling the crush point holes
|
|
snake
Heat Winner
Posts: 368
|
Post by snake on Oct 20, 2017 9:11:29 GMT -5
|
|
snake
Heat Winner
Posts: 368
|
Post by snake on Oct 8, 2017 11:35:42 GMT -5
results
|
|
snake
Heat Winner
Posts: 368
|
Post by snake on Sept 23, 2017 11:01:06 GMT -5
trailer hitch might not pass inspection
|
|
snake
Heat Winner
Posts: 368
|
Post by snake on Sept 11, 2017 7:27:12 GMT -5
Distributor protectors are allowed, it cannot touch anything, you must cut firewall out behind it! - -
What u say willis
|
|
snake
Heat Winner
Posts: 368
|
Post by snake on Aug 30, 2017 22:09:52 GMT -5
|
|
snake
Heat Winner
Posts: 368
|
Post by snake on Aug 29, 2017 9:44:15 GMT -5
|
|
snake
Heat Winner
Posts: 368
|
Post by snake on Aug 28, 2017 19:10:40 GMT -5
stock uppers control arms just re sliced re welded , it jammed against the springs for extra support , could swap out for gm tie rods using gm stock spindles
|
|