|
|
Post by sdcland19 on Dec 20, 2012 14:29:05 GMT -5
what is the thickest rim/ toughest rim out there
|
|
88x
Heat Winner
Posts: 247
|
Post by 88x on Dec 20, 2012 14:35:24 GMT -5
Stock wheels? alot of people like the Chevy SS wheel not sure how thick they are tho  |
|
|
|
Post by STROMI 121 on Dec 20, 2012 15:14:28 GMT -5
SS wheels with weld in centers.
|
|
|
|
Post by farmboy012 on Dec 20, 2012 15:49:18 GMT -5
SS wheels with weld in centers. X2 Then Mazda 6 lug |
|
61j
Heat Winner
Posts: 503
|
Post by 61j on Dec 20, 2012 15:57:28 GMT -5
I feel ss are junk. Mazda are almost 5/16" or so thick.
|
|
|
|
Post by sdcland19 on Dec 20, 2012 16:47:33 GMT -5
yes stock rims 88x,, what mazda rims are you usings 61j
|
|
|
|
Post by leadsled71 on Dec 20, 2012 17:25:40 GMT -5
I had good luck with the chrome ford F150 wheels. axles were bent bad, but rims were still staright. and that was with the stock centers. I have a stock pile of big bolt chrome buick rallies but havent tried them yet
|
|
|
|
Post by smashincwa on Dec 20, 2012 18:45:28 GMT -5
Pontiac ralleys
For 5X 4 3/4 pattern, the monte 73-75 rim turbine rim.
|
|
|
|
Post by weldedmess on Dec 20, 2012 18:48:33 GMT -5
Dodge van rims.....around a 95 style....dont have a pic
|
|
|
|
Post by Wreckandrace on Dec 20, 2012 19:09:32 GMT -5
I had good luck with the chrome ford F150 wheels. axles were bent bad, but rims were still staright. and that was with the stock centers. I have a stock pile of big bolt chrome buick rallies but havent tried them yet Buicks are softer than stock steel rims.IMO... |
|
|
|
Post by carson29 on Dec 20, 2012 20:14:08 GMT -5
 IMO these are the strongest wheels made with or with out weld in centers. |
|
|
|
Post by homer2 on Dec 20, 2012 20:17:35 GMT -5
I know everyone wants the strongest wheel.
But, what good is a strong wheel if you get a bent or broken axle?
I would rather have my wheel bend a little and save my rear end.
Homer
Get it, save my rear end. ;D
|
|
|
|
Post by bangmup07 on Dec 20, 2012 20:26:38 GMT -5
That is a good point homer. Its mainly to keep the tire on the bead. For better manouver ability. And height if you was to get a flat. I'm getting some geo tracker rims and welding centers in.
|
|
|
|
Post by 3sasquach on Dec 20, 2012 22:04:13 GMT -5
If you dont care about breaking stuff, Not much beats a double skinned stock wheel. You do need the right type of wheel to do this however. Forklift wheels are next in my line up ( weld in center ), And then the early gm ralleys. IMO
|
|
61j
Heat Winner
Posts: 503
|
Post by 61j on Dec 20, 2012 22:23:08 GMT -5
yes stock rims 88x,, what mazda rims are you usings 61j Not sure found them at a you pull it, already off they were chrome six bolt rims. |
|
