|
Post by davis03 on Feb 12, 2013 20:56:58 GMT -5
i have a 4.3 vortec im converting to carb will a 4 barrel marine intake fit any carb and will any hei 4.3 fit it? I'm using the stock 5 speed with it with 355 gears in a 8.75 good or bad idea. thanks pm if u want
|
|
|
Post by krazy-k on Feb 14, 2013 8:26:07 GMT -5
i use the 4 marine barrel intake i have a 2 barrel rog on it and hei dis in it mine runs like a champ just have 2 dial the carb in
|
|
|
Post by krazy-k on Feb 14, 2013 8:27:29 GMT -5
i dont know much about gearing yet
|
|
|
Post by davis03 on Feb 14, 2013 19:55:22 GMT -5
Ok thanks man I guess I'm goin to try it and see what gears that little guy likes.
|
|
|
Post by krazy-k on Feb 15, 2013 3:42:15 GMT -5
i run 3-speed
|
|
|
Post by davis03 on Feb 15, 2013 20:40:28 GMT -5
well i was pondering that I have a saginaw three speed that I just bought with that shatterproof bell housing.
|
|
|
Post by krazy-k on Feb 15, 2013 22:36:12 GMT -5
i had 373 gears but im going 2 get 411 or higher took 2 long 2 really get up 2 speed i want more snap
|
|
|
Post by hill32 on Feb 21, 2013 16:49:00 GMT -5
Will a dp for a 350 bolt and work on a 4.3?
|
|
-75x-
Heat Winner
Keepin' Em Strait... Since 08'
Posts: 863
|
Post by -75x- on Feb 21, 2013 17:15:05 GMT -5
i dont see why it wouldnt... cradle works with minimal mods..
|
|
|
Post by bill987 on Feb 21, 2013 19:32:46 GMT -5
if your dp omnly bolts to your bell housing it will work
|
|
-75x-
Heat Winner
Keepin' Em Strait... Since 08'
Posts: 863
|
Post by -75x- on Feb 21, 2013 22:17:02 GMT -5
^^^ are the back intake bolts different? i could see a halo n shit not workin.. but a old school home-made one.. should work right?
|
|
|
Post by krazy-k on Feb 23, 2013 17:39:24 GMT -5
the 350 tranny will bolt straight on a 350 cradel will all the same bolt holes just diffrent header flanges and intake holes
|
|
|
Post by twistedpleasure777 on Feb 24, 2013 19:15:52 GMT -5
if you are trying to put a carb on a vortec set of heads buying the edelbrock aluminum 4.3 vortec intake is well worth it alittle over $200 bucks and you wont have any headaches
|
|
|
Post by undertaker25 on Feb 28, 2013 9:53:27 GMT -5
I am building a 4.3 vortec...it has an aluminum oil pan on it...I was told that a steel oil pan from an older 4.3 will not bolt up...is this true? If so, is there a steel oil pan out there that will bolt up to it?
|
|
|
Post by hill32 on Mar 20, 2013 20:58:19 GMT -5
Im get gas pushing back through my carburetor.. what u guys think burnt valve, dead cylinder or what?
|
|