|
|
Post by runinoutofgas on Jul 15, 2015 18:51:33 GMT -5
Test the ohms any less than 11.9 it's junk. Easy access on 3300
|
|
|
|
Post by wideopenmudsports8^ on Jul 16, 2015 0:32:40 GMT -5
Also on these if u got spray on like 3 injectors and not the rest before u replace anything, i just had this problem. I unplugged the temp sensor and she fired up.
|
|
|
|
Post by ghall79 on Jul 16, 2015 17:35:07 GMT -5
The high mounted rear bumper trick works great on these cars   Do you remember how high the bumper was. My rules say that the center of the bumper can only be 24in from the ground. And did you have to drill any new holes? |
|
|
|
Post by STROMI 121 on Jul 16, 2015 18:47:45 GMT -5
I put the bottim studs in the top holes and drill new top holes.
|
|
|
|
Post by STROMI 121 on Jul 16, 2015 18:48:41 GMT -5
Im not sure on the height
|
|
|
|
Post by sickels on Jul 16, 2015 22:05:06 GMT -5
I got roughly 15.5 on all 6 injectors.... hmmm.
|
|
|
|
Post by taterjuice on Jul 17, 2015 1:56:22 GMT -5
I got roughly 15.5 on all 6 injectors.... hmmm. I would more concerned with lack of spark, unless you solved that problem it won't matter if you injectors are junk. |
|
|
|
Post by sickels on Jul 17, 2015 7:02:37 GMT -5
What the beck could be causing it.. firing order is right. New balancer. New crank sensor. New plugs. Swapped coil pack. Icm tested good.
|
|
|
|
Post by taterjuice on Jul 17, 2015 8:06:29 GMT -5
What the beck could be causing it.. firing order is right. New balancer. New crank sensor. New plugs. Swapped coil pack. Icm tested good. Ecm or wires from crank sensor to ICM |
|
|
|
Post by sickels on Jul 17, 2015 8:29:26 GMT -5
How can I test the ECM though?
And I'm gonna trace the wires.
But even if it is just weak orange spark, it's spark and spark should ignite the fuel.
|
|
|
|
Post by taterjuice on Jul 18, 2015 3:08:34 GMT -5
How can I test the ECM though? And I'm gonna trace the wires. But even if it is just weak orange spark, it's spark and spark should ignite the fuel. if you got spark toss some injectors at it and see what happens. |
|
|
|
Post by ghall79 on Jul 18, 2015 19:45:53 GMT -5
What wires are 100% necessary for a 2.8 with fi? I already got rid of everything under the dash except for the wires going to the ignition and fuse box. I'm assuming that all of the wires from the computer are necessary? Not really sure. I know there is a lot of stuff from the computer through the firewall and I would like to eliminate some if I can. Thanks
|
|
|
|
Post by ghall79 on Jul 18, 2015 19:49:16 GMT -5
And also do you guys notch the subframe on these? Or what other things help make them go up. Cause every a-body car I've seen plows straight down after one hit
|
|
|
|
Post by C4 on Jul 18, 2015 20:47:12 GMT -5
And also do you guys notch the subframe on these? Or what other things help make them go up. Cause every a-body car I've seen plows straight down after one hit Sub, no. Rear uni-rails, yes.   |
|
|
|
Post by ghall79 on Jul 19, 2015 12:40:44 GMT -5
And what about the wires? How minimal can it get?
|
|
