|
Post by gmjake on Sept 19, 2017 13:13:52 GMT -5
Question can I bolt a carb to a TBI INTAKE I'm having a hard time finding a carb intake
|
|
hicks66
Heat Winner
bumper
Posts: 386
|
Post by hicks66 on Sept 19, 2017 18:16:12 GMT -5
Question can I bolt a carb to a TBI INTAKE I'm having a hard time finding a carb intake yes you can I had some pics of the one I did with a one barrel Motorcraft in this thread but I'm sure photo bucket of sh!t has made them go away. I just built an adapter it was 1/2 aluminum top and bottom with a short piece of inch and half pipe between them worked really good
|
|
|
Post by hitnget199 on Jan 6, 2018 20:51:16 GMT -5
I have a 2.5l that came out of a 1989 s10. I'm wanting to change out the throttle body and put a carb on it. Does any body know how I would go about doing this and what else I'll have to do to do this?
|
|
|
Post by Luke Wells on Jan 6, 2018 20:54:02 GMT -5
I have a 2.5l that came out of a 1989 s10. I'm wanting to change out the throttle body and put a carb on it. Does any body know how I would go about doing this and what else I'll have to do to do this? [br Read the post right above yours.
|
|
hicks66
Heat Winner
bumper
Posts: 386
|
Post by hicks66 on Jan 6, 2018 21:28:49 GMT -5
Pics on first page I can still see them so maybe everyone else can to
|
|
|
Post by hitnget199 on Jan 15, 2018 14:34:28 GMT -5
Pics on first page I can still see them so maybe everyone else can to What kind of distributor did you end up using and how you run your wiring?
|
|
hicks66
Heat Winner
bumper
Posts: 386
|
Post by hicks66 on Jan 15, 2018 14:47:26 GMT -5
I used factory setup didn't change anything other than intake and low pressure fuel pump, hot wired ignition
|
|
|
Post by Teamsleven777 on Jan 29, 2018 1:24:57 GMT -5
Anyone know if a 1990 tech 4 s10 motor will fit into a Lumina. I know it's the 60 degree bellhousing but mainly concerned about Accesory clearance mainly water pump. Has anyone attempted this?
|
|
|
Post by C4 on Jan 29, 2018 1:31:37 GMT -5
Anyone know if a 1990 tech 4 s10 motor will fit into a Lumina. I know it's the 60 degree bellhousing but mainly concerned about Accesory clearance mainly water pump. Has anyone attempted this? 80% sure the starter is on opposite sides.
|
|
olsen15
Feature Winner
Posts: 1,236
|
Post by olsen15 on Jan 31, 2018 7:32:18 GMT -5
Anyone know if a 1990 tech 4 s10 motor will fit into a Lumina. I know it's the 60 degree bellhousing but mainly concerned about Accesory clearance mainly water pump. Has anyone attempted this? 80% sure the starter is on opposite sides. Yep starter is on the wrong side. Fwd and Rwd motors have starters on the opposite sides.
|
|
|
Post by shitbreaksj49 on Feb 16, 2018 4:37:31 GMT -5
What will I have to do to get a 3100 motor and trans to fit on a cradle that had a 2.5
|
|
|
Post by juicyjdawg on May 8, 2019 1:05:08 GMT -5
What is a good carb to run on an 82 rwd iron duke w/head n cam work done?
|
|
|
Post by gavdaman on Oct 27, 2021 13:39:17 GMT -5
I got a Chevy citation 4 speed fwd with the iron duke clean barn car building for compact next year in Ohio looking for tips and tricks
|
|
|
Post by smashbob12 on Oct 28, 2021 4:58:30 GMT -5
I got a Chevy citation 4 speed fwd with the iron duke clean barn car building for compact next year in Ohio looking for tips and tricks Hatch or trunk ??
|
|
|
Post by x13mopar on Dec 8, 2022 1:26:06 GMT -5
Anyone still read these?
If I remember, the bellhousing pattern is the same for all dukes and the 2.2 found in s10s, and the 3.4 in camaros,both of which have the starter on the drivers side?
Engines with DIS, are they machined for a distributor but have some sort of plug or are they sealed off?
What machining is required for a mercruiser 140/3.0 crank?
|
|