|
Post by pdex982 on Feb 1, 2015 16:23:27 GMT -5
Are the axles from mid 70s regal or Grand Prix the same length as the fullsize cars. Found some at a yard but was t sure if they were the same or not.
|
|
|
Post by 383 Sonoma on Feb 1, 2015 19:27:29 GMT -5
no sir
|
|
|
Post by derby2racer on Feb 2, 2015 6:49:10 GMT -5
Anyone know what gears came from factory in 72 impala?
|
|
|
Post by pasterofmuppets on Feb 4, 2015 10:15:49 GMT -5
2:73
|
|
|
Post by derby2racer on Feb 4, 2015 23:53:14 GMT -5
Thanks. Anyone know the cheapest place to find rear end gears for these? hoping to get some that are around 4:10. Thanks
|
|
|
Post by pdex982 on Feb 7, 2015 18:57:43 GMT -5
Does the raptorfab conversion spool take special shims or will any factory ones work?
|
|
|
Post by William Mullins 76x on Feb 13, 2015 21:49:12 GMT -5
Does any one know if 10 BIA rear end backing plates are the same as 10 bolt c clip rear end backing plates?
|
|
|
Post by pasterofmuppets on Feb 13, 2015 23:27:10 GMT -5
Thanks. Anyone know the cheapest place to find rear end gears for these? hoping to get some that are around 4:10. Thanks If its a 10 bolt you can find gears just about anywhere (Richmond, Speedway, even on eBay cheap). If its a 12 bolt... there are no gears available.
|
|
|
Post by derby2racer on Feb 14, 2015 0:56:44 GMT -5
Yeah its a 10 bolt. Just didnt know if anyone knows what place is cheapest.
|
|
|
Post by pasterofmuppets on Feb 14, 2015 6:02:43 GMT -5
Dont skimp on quality just because of price. Richmond makes solid gears that are proven at a decent price.
|
|
|
Post by crusher71 on Feb 14, 2015 10:35:57 GMT -5
DEEPEST "FACTORY" GEARS FOR A 71-76 10 BOLT WOULD BE 3.73 OBVIOUSLY AFTERMARKETS ARE OUT THERE BUT WITH THE ADVENT OF STOCK RULES, BE CAREFUL WHAT YOU RUN....AND THE DEEPEST FOR THE 12 BOLTS ARE 3.42 RIVIERA GS ONLY..
|
|
|
Post by lahnen on Feb 17, 2015 9:51:37 GMT -5
Probably asked before, 10bolt bia shafts all same length in full size rears or was there different lengths
|
|
|
Post by STROMI 121 on Feb 17, 2015 12:44:15 GMT -5
Probably asked before, 10bolt bia shafts all same length in full size rears or was there different lengths I think it matters what size car it came in. Fullsize or midsize. IDK?
|
|
|
Post by 383 Sonoma on Feb 17, 2015 13:44:18 GMT -5
Dont skimp on quality just because of price. Richmond makes solid gears that are proven at a decent price. I've had good luck with Yukon gears.... A lot of it is in setting them up.... That can make or break the life span of a ring and pinion. .... But I will not argue that Richmond makes a good gear.... Ran them for years....
|
|
|
Post by 383 Sonoma on Feb 17, 2015 13:46:43 GMT -5
Does the raptorfab conversion spool take special shims or will any factory ones work? You will probably need to get a carrier shim kit from the parts store. They aren't expensive. Every housing is a little different so you may get by with the ones that were in it but probably not.
|
|