demoboy333
Feature Winner
Enter your message here...
Posts: 3,124
|
Post by demoboy333 on Apr 30, 2022 22:16:59 GMT -5
|
|
demoboy333
Feature Winner
Enter your message here...
Posts: 3,124
|
Post by demoboy333 on Apr 30, 2022 22:24:32 GMT -5
|
|
demoboy333
Feature Winner
Enter your message here...
Posts: 3,124
|
Post by demoboy333 on Apr 30, 2022 22:55:01 GMT -5
Also there was 7 ground wires total that I had to relocate.
|
|
demoboy333
Feature Winner
Enter your message here...
Posts: 3,124
|
Post by demoboy333 on May 2, 2022 21:22:22 GMT -5
Update. Fired it up today after stripping it. No theft issues. Pulling up to garage to finish cage and weld on bumper. Weekend is right around corner. As a limited weld fullsize builder its very hard not to add the extras!
|
|
demoboy333
Feature Winner
Enter your message here...
Posts: 3,124
|
Post by demoboy333 on May 4, 2022 13:36:03 GMT -5
Looks like my show got canceled due to it being to wet so ill keep building but may not run it till July.
|
|
demoboy333
Feature Winner
Enter your message here...
Posts: 3,124
|
Post by demoboy333 on May 11, 2022 17:08:19 GMT -5
Since derby got rained out I ordered a derby ECM for the van. Suppose to be plug and play ECM but said some models have to run a press button for the starter once you swap it. I've got the halo in and then roof and quarters done and started wiring doors shut. Since I have more time I'm going to trim down the harness since they security system has been taken off I won't trip it. A derby wiring harness for it is $300 bucks and thats my harness shipped to him to do and send back since he's out of my harnesses at moment.
|
|
demoboy333
Feature Winner
Enter your message here...
Posts: 3,124
|
Post by demoboy333 on May 15, 2022 19:51:25 GMT -5
Did a heated dimple since I can't notch at this gut & go show(dimple/prebend only) Got doors just about wired shut. Going to add some extra door protection. Still have to weld on bumper and swap rear tires.
|
|
demoboy333
Feature Winner
Enter your message here...
Posts: 3,124
|
Post by demoboy333 on May 18, 2022 12:22:05 GMT -5
Update.
- wired fans, fuel pump and started to switch panel. -Swap rear tires to donuts -Found the idle screw to idle up the car manually. The ecm is suppose to raise idle after engine is hot.
Got parts ordered to come in to raise the front up with no welding.
|
|
demoboy333
Feature Winner
Enter your message here...
Posts: 3,124
|
Post by demoboy333 on Jun 11, 2022 22:58:18 GMT -5
Update. Having to send the ecm in due to when chopping thottle it trys to die. Swapped it with buddy's ecm runs good and fine on factory ecm. Backwoods was very helpful said send it back he will flash it to fix it. Got the bumper mounted.
|
|
Landshark007
Feature Winner
I'm not here to win I'm here to make sure you don't win
Posts: 4,228
|
Post by Landshark007 on Jun 14, 2022 17:43:55 GMT -5
Like the caddy bumper lol
|
|
|
demoboy333
Feature Winner
Enter your message here...
Posts: 3,124
|
Post by demoboy333 on Jul 7, 2022 10:24:08 GMT -5
Update of small things done.
-Fuel pump seemed weak so swapped it. -Put a heavy cap on radiator. -Two bottles of water wetter. -Turned a bottle into the radiator overflow. -Spray foamed around radiator. -Wrapped ECM with mud flap and mount in firewall area and added some spray foam for some give. -Chained the top motor mount to core support. -Added 9 wire from c pillar to c pillar high and low to help with holding pulled inward for bellying.
|
|
demoboy333
Feature Winner
Enter your message here...
Posts: 3,124
|
Post by demoboy333 on Jul 8, 2022 20:12:48 GMT -5
|
|
demoboy333
Feature Winner
Enter your message here...
Posts: 3,124
|
Post by demoboy333 on Jul 8, 2022 21:19:11 GMT -5
Tomorrow's the day we figure out how these vans hold up. One is loaded other is mine and im a bit superstitious on preloading. Always had really badluck if I load the night before.
|
|
Landshark007
Feature Winner
I'm not here to win I'm here to make sure you don't win
Posts: 4,228
|
Post by Landshark007 on Jul 9, 2022 16:09:48 GMT -5
Good luck
|
|