bloomer wi augs 5th 2022 7pm start time

[mewes5x]

FWD Weld Midsize

1st $1,000.00 + Big Money Check
2nd $700.00 + Trophy
3rd $400.00 + Trophy

Compact truck, SUV & Mini Vans

1st $1,000.00 + Big Money Check
2nd $700.00 + Trophy
3rd $400.00 + Trophy

FWD Chain Midsize

1st $1,000.00 + Big Money Check
2nd $700.00 + Trophy
3rd $400.00 + Trophy


Power wheels (ages 4 -10)

To be run from 7pm to 7:30 pm
All entries receive a trophy
Call 715-222-9368 for more information

[mewes5x]

Nlr Promotions FWD Mini Vans/ suv
- No welding struts, tie rods, motor mounts, etc. unless using your allowed plates on these items. Rules are simple, follow them. If it says you can’t do it, pretty much you can’t do it.
• General Rules
1) No full-size vans or SUV’s, Front Wheel Drive only.
2) No welding unless rules say.
3) You may have a floating 4-point cage with halo, you may have a floating gas tank protector that follows the tank. Gas tank protector cannot go past rear axle.
4) All body mounts must be factory unless rusted out. If rusted out, change with same size bolt and leave stock pucks in.
5) Wire, weld or chaining of the doors, trunk lid, and hood is allowed. Max of (2) per seam allowed, (4) are allowed in the hood. 2 threaded rods may be welded to the top of frame. 6) Fuel cell may be mounted on the back-seat bar and 2” away from back seat area. 7) Aftermarket gas pedal, brake pedal, shifter, and headers are allowed.
8) You may put a car bumper on, 6” from bumper backing you may use a bracket to weld it on, anything past 6” will be cut off! You can also put a 6”x4” piece of tubing on instead. No loaded bumpers, seam welded is fine!!
9) Any tire is allowed.
10) All plastic, lights, and glass must be removed.
11) Pre-ran car fix it plates (2) 5x5 ¼” plates. these can be used to weld bumper back on if you need to. Plates cannot be split up, must stay 5x5”. If those 2 plates aren’t enough, build a new car. 12) Drivers door can be welded shut fully, or a door plate may be used.
13) Any engine or transmission may be used but it must be bolted in with factory mounts. Absolutely no welding to swap them! You can carb convert an EFI engine in this class. 14) Only stock driveshafts are allowed!
15) Fresh vans allowed (2) 5x5x1/4” plates, which can be used as you want. These can be used on motor mounts, struts, tie rods, etc.

[mewes5x]

Nlr Promotions FWD Midsize Chain
Front Wheel Drive Cars Only- No welding struts, tie rods, motor mounts, doors, etc. We are looking for an easy, throw together, fun cars! If you want to do more then what is allowed, we have a weld class! Rules are simple, follow them. If it says you can’t do it, pretty much you can’t do it. Strip the car, weld the cage, move your battery and gas tank, chain doors and put a bad a** paint job on it.
• General Rules
1) No welding unless rules say.
2) You may have a floating 4-point cage with halo, you may have a floating gas tank protector that follows the tank. You will be allowed uprights for safety around the tank with kickers connecting to your halo bar. This is for safety only, judge’s discretion if it is used in other ways.
3) All body mounts must be factory unless rusted out. If rusted out, change with same size bolt and leave stock pucks in.
4) Wire or chaining of the doors, trunk lid, and hood is allowed in (6) locations. 5) Fuel cell may be mounted on the back-seat bar and 2” away from back seat area. 6) Aftermarket gas pedal, brake pedal, shifter, and headers are allowed.
7) You must use stock bumper off the car! You may add 4 bolts to it to help hold it on. If stock bumper is plastic, you can change with a tin stock one off another FWD style car. Bumpers can be welded on, no compact/full size bumpers, we will enforce this heavily!
8) Any tire is allowed.
9) All plastic, lights, and glass must be removed.
10) Pre-ran car fix it plates (2) 5x5 ¼” plates. these can be used to weld bumper back on if you need to. Plates cannot be split up, must stay 5x5”. If those 2 plates aren’t enough, build a new car. 11) Drivers door can be welded shut.
12) You can clamp up your suspension to the desirable ride height.
Rules Questions? Contact Jon- 715-222-9368

[mewes5x]

Nlr Promotions FWD Midsize Weld
Front Wheel Drive Cars Only- These are a step up from the chain rules, this is still meant to be a simple build, just with a little stronger car, not a full-blown mod! Rules are simple, follow them. If it says you can’t do it, pretty much you can’t do it.
• General Rules
1) No welding unless rules say.
2) You may have a floating 4-point cage with halo, you may have a floating gas tank protector that follows the tank. You will be allowed uprights for safety around the tank with kickers connecting to your halo bar. This is for safety only, judge’s discretion if it is used in other ways.
3) All body mounts must be factory unless rusted out. If rusted out, change with same size bolt and leave stock pucks in.
4) Wire, weld or chaining of the doors, trunk lid, and hood is allowed. Max of (2) per seam allowed on doors and trunk. Trunks may have up to ¾” threaded rod and (4) welded plates not to exceed 3”x5”x1/8” thick, or (6) spots of chain/9 wire. Trunks may be dished and folded 90 degrees. Hoods may have up to ¾” threaded rod in (6) spots. The front (2) can go through the frame, the other (4) can only be welded to tin and cannot exceed 8” long.
5) Fuel cell may be mounted on the back-seat bar and 2” away from back seat area. 6) Aftermarket gas pedal, brake pedal, shifter, and headers are allowed.
7) You may put a car bumper on, 6” from bumper backing you may use a bracket to weld it on, anything past 6” will be cut off! You can also put a 6”x4” piece of tubing on instead. Loaded bumpers/seam welding is allowed. Manufactured bumpers are allowed, as long as they follow the same shape and size as a factory bumper.
8) Any tire is allowed.
9) All plastic, lights, and glass must be removed.
10) Pre-ran car fix it plates (2) 5x5 ¼” plates. these can be used to weld bumper back on if you need to. Plates cannot be split up, must stay 5x5”. If those 2 plates aren’t enough, build a new car. 11) Drivers door can be welded shut.
12) You can clamp up your suspension or weld in a piece of steel to the desirable ride height. Must have stock springs and look like a factory strut!
13) Welding or bracing tie rods is allowed. Aftermarket tie rods are allowed.
14) You can carb convert an EFI engine in this class. You are allowed a basic halo to protect the carb, please call if you don’t understand what basic means! This is to protect the carb, not strengthen the car!
15) Engine mounts can either be reinforced or replaced with a 2”x2” piece of square tube. 16) Sheet metal rust can be repaired with same thickness material, leave rust there! If you are second guessing yourself, call!
17) Trailing arms cannot be reinforced.
18) Body creasing is allowed.
19) (2) extra body mounts allowed from frame to sub-frame. 4” on each only.
20) If not using rule #19, you get (2) 4x4” plates to use firewall forward however you want. 21) Rear window bar is allowed, material not to exceed 2x2”. Only 6” is allowed on roof and 6” on trunk.
Rules Questions? Contact Jon- 715-222-9368