|
Post by hellbent09 on Oct 1, 2012 17:29:46 GMT -5
I'm going to be leafing one as soon as I find a rear end big enough to swap too
|
|
|
Post by hvyeqop on Oct 1, 2012 17:47:41 GMT -5
will the rear out of 74-76 old iron cars fit under these cars?
|
|
|
Post by dirttrackbandit525 on Oct 1, 2012 19:23:44 GMT -5
let me know how it goes post pics might have to try it
|
|
|
Post by hellbent09 on Oct 12, 2012 14:29:52 GMT -5
Would a crown Vic rearend fit under a camaro. If not what would be close or a better rearend
|
|
|
Post by hellbent09 on Oct 13, 2012 5:48:43 GMT -5
??
|
|
|
Post by antnee66 on Oct 13, 2012 21:28:29 GMT -5
Would a crown Vic rearend fit under a camaro. If not what would be close or a better rearend[/quote]
I don't know anything about a camaro's! But I do know if the Vic rearend is to wide you could run lumina wheels on it! Fwd wheels are offset enough to put your tires up under the body. And they have the same bolt pattern. Hope this help I have seen in done on fox body's!
|
|
|
Post by hellbent09 on Oct 14, 2012 14:13:35 GMT -5
OK ill check into that what different size rearends come in a crown Vic anyone know
|
|
|
Post by sceard55x on Oct 14, 2012 16:33:14 GMT -5
Hellbent ill go measure them tomoroww and let you know what I find
|
|
Vito324
Feature Winner
For badass roof signs, Check out BlackFlag Designs on Facebook!
Posts: 2,189
|
Post by Vito324 on Oct 14, 2012 16:34:51 GMT -5
You'd have to trim that vic rear down a couple inches. Won't fit if its stock measurements.
|
|
|
Post by hellbent09 on Oct 14, 2012 17:28:34 GMT -5
It don't necessarily have to be a Vic rearend. Just looking for a better one. What car other than a camaro would work and be a little better
|
|
|
Post by sceard55x on Oct 14, 2012 18:36:07 GMT -5
I'll no for sure tomorrow but I think a mid size rear is close but ill let u know for sure
|
|
Vito324
Feature Winner
For badass roof signs, Check out BlackFlag Designs on Facebook!
Posts: 2,189
|
Post by Vito324 on Oct 15, 2012 2:22:02 GMT -5
I believe a 70's midsize GM 10 bolt will go in these but 100% sure.. You have to make a mount for the torsion arm though.
|
|
|
Post by hellbent09 on Oct 15, 2012 3:40:05 GMT -5
I'm leafing mine
|
|
|
Post by ducky29 on Oct 16, 2012 17:15:32 GMT -5
60s y framers with narrow 8-3/4 will fit perfect same thing with a 28 spline 9 inch from a 60s t bird or galaxy. when i leafed mine i used the stock trailing arm bracket and bolted the front there and had the leafs under the rearend
|
|
|
Post by ducky29 on Oct 16, 2012 17:17:32 GMT -5
will the rear out of 74-76 old iron cars fit under these cars? it will work but sticks out 1.5 to 2 inches on each side
|
|