Post by nickn44 on Mar 31, 2019 20:51:26 GMT -5
2019 Jim Falls Lions Sturgeon Fest
Jim Falls located northeast of Eau Claire, Chippewa area of Wis.
Friday August 30TH @ 730pm
Classes:
Semi stock full size (replaces chain class) open to any year except no 74 and older Imperials, no 03 and newer automobiles, no suicide door Lincolns and no leaf sprung wagons.
Semi stock Midsize
Compact car class ***WILL FOLLOW MIDSIZE RULES UNLESS OTHERWISE NOTED***
Mini Vans
(MOVED TO SUNDAY),Youth midsize ages 13-19 using semi stock midsize rules...100% payback and trophy.(MOVED TO SUNDAY)
All classes $50 to enter,
***** Payouts: Back to the 90's $2000, 1500, 500, 250 ..$100 heat wins. Midsize: 800, 500, 250,.$1000 to win at 20 cars, Compacts: 700.00, 400, 200 one shot deal, mini vans 100% payback PLUS 500, BONUS ONCE WE HIT 20!
**Semi stock full size: This class is designed as a mainly oem class, Simple class with no gray areas. 1st rule is no aftermarket parts such as DP's, steel bell housings, Trans protectors, truck or after market trans cases, extreme cradles, etc., no stubbing, no frame swaps. no tilting.
****If its not in the rules you CANNOT do it!
**Preparation: All glass, lights, chrome, plastic, carpet, header panels, hubcaps, complete trailer hitches, gas tanks and debris etc must be removed.
**Safety: Helmets, eye protection, and protective clothing required! All air bags must be unbolted and removed, no cutting out just air bag.
**Gas tanks and battery (up to 2) automotive must be relocated. Gas tank on floor behind driver or centered behind driver on floor or off rear bar, battery box on front passenger floor area. Must not be used to strengthen car. Any gas tank protector must come off rear bar and be at least 6" off floor...can be tight to rear seat tin but no altering of tin in any way... NO WIDER THAN 30"
**Hoods and trunks : Hood (4)spots chains (36") or wire (4 loops) or rods to secure hood. If using rods, maximum is 3/4" in diameter and 2 must run through core support (4" max spacer)in front and 2 may run sheet metal to sheet metal only. Trunks 4 spots with 4 chains (30") 4 wires (4loops) or 2 rods, and 2 chains or wire. Rods must go through factory body mounts vertically in back, or welded to frame between mounts only. Hood, and trunk top plates not to exceed 6" by 6" square. Hood must be cut out for fires with maximum 4 bolts 3/8" per opening. Trunks may have 90 degree bend but must have 50% stock location. No bending down or wedging, simple 90 degree bend that's all. 2 chains in windshield opening to protect from hood. Tailgates 4 chains only 36" long, no threaded rods in tailgates of wagons.
**Body Forming: You may body form but no wedged trunks, 6" max dish.
**Doors : 2 spots per vertical seam 30" by 3/8 chain or 1 6 inch weld with 2" by 6" 1/4 plate max. drivers door may have unlimited.
**Safety cage. Basic 4 point with halo bar. Consists of dash bar above steering, 2 door bars mounted to dash and seat bars middle height area of door, 1 bar behind seat positioned midway height of seat horizontally. No bar larger than 6" in diameter, No plate to mount bars larger than 8" square. No kickers, just safety chain to sheet metal directly down from center of rear bar if only running rear bar. Halo bar off rear seat bar only, may be bolted to roof tin in 2 spots. Door bars may not go further back than 6" from center pillar or further forward than dash bar.
**Body bolts" May be replaced with up to 7/16" bolt max, body pucks may be removed. Washers no larger than 3" to be used. Do not get creative here.
**Transmission coolers are allowed but must be securely mounted and not do anything other than cool the trans. No trans protector, or steel or aluminum bells except contoured ultra, no steel tails, no aftermarket or truck trans cases, only stock mount or remove, stock cross members only, or 2x2 steel tube. May have aluminum ultra bell on previously broken trans and needed to be able reuse trans. Only mid plates are to change trans bolt pattern with no more than 1" wider.
**Engines: Vertical headers yes, Engine swaps yes, (VERY basic) engine cradle will be allowed with factory or after market frame mounts but must have rubber grommets. Pulley protector ok but must not at any time touch sway bar or instant DQ.
**Suspension: 15" minimum to lowest point of rear frame or bumper, 20" maximum to bottom of front bumper. You may use spring spacers, straps, bolting (1/2") bolts, or rod (3/4")max from lower a-arm to bottom of spring bucket to obtain this only, (2) 2"x6" straps per side must go directly down to spring bucket. 1 spot per side up
to 3/8" diameter by 30" chain can be used to hold in springs for rear end on sedans or wagons. No rods in rear shock area. (No reinforcing of suspension components). You may use watts conversion 1/4" or less or weld in pkg tray for 98-02s, and no more than 1" overlap for tray.
**Rear ends: Any factory rear end, can be reinforced with any size axle. No homemade rear ends and cannot reinforce car in any way. Pinion brake ok. Must use stock OEM control arms.
**Frames: No welding other than brackets for bumpers, or where specified in rules, you may dimple or notch rear frames.
**Bumpers of choice, may be reinforced. Substitute maybe be rectangular steel no wider than car, max 6" tall by 6" wide max up to 3/8" thick. Recommend welding stock chrome to make a factory appearing bumper. No filling aftermarket. You may hard nose but all shocks must be removed, Or shocks and brackets in factory position may be welded with single pass, no front and rear bracket swaps. No welding further back than 8" from center of core support hole.
I will allow 2 spots per bumper of wire or chain. May go to core support or frame only not around threaded rod or hood. Nothing excessive or you will remove it all. 5 3/8" fender bolts allowed per fender.
**Steering...aftermarket or homemade steering.. After market brakes and shifting components are fine, just do not reinforce car in any way with these components.
**Tires of choice up to 30" tall, valve stem protectors ok.. Any wheel that started as a factory wheel, no bead locks.
ONLY AFTER MARKET PARTS** gas pedal, steering , transmission or floor mounted shifter nothing hanging down near cross member, dash or bar mounted brake unit or plate for manual brakes..basic engine cradle..aluminum factory type radiator in factory position, and slider drive shafts.
****80 and newer metric cars will be allowed a (1) per side 3/8" 18x4" rear hump plate centered on rear hump.
****Gas tank protectors will allowed off rear seat bar only, no wider than 30" by 4" at the rear seat area, they may touch but do not alter floor to make tighter or you will be loaded, must be 8" off floor.
****rear window bars will be allowed, no more than 4" in diameter, bolted or welded to roof, and bolted only with 2 bolts in speaker deck and 2 bolts in trunk lid.
Semi stock midsize:
Mid-Size 4-Cyl. And 6-Cyl.,8-Cly ONLY, no full framed cars. No wheel base over 113"
Cars must have all airbags and charges removed by unbolting not cutting out just air bags. You must remove all glass and carpet, headliner, in addition to flammable materials though dash may remain intact . All mirrors, chrome, plastic, fiberglass header panels, factory gas tank , hitches must be removed.
*Hoods and trunks: 4 Spots Maximum in each...Choice 4 chains (24"), 4 spots wire (4 loops) maximum, or combination of 2 3/4" threaded rod at core support area only with 2 chains or wire. Trunk choices 4 chains, wires, or plates (6x2x1/4") or 2 3/4" rods and 2 chains, 2 plates (2x6x1/4") or wire... 12" round or square hole cut in hood in case of fire. All hood and trunk hold down plates to not exceed 6x6x 1/4”, __ body forming allowed just do not over do it...4" dish in trunk lid max__, but you will be allowed 1 90 degree bend in trunk lid. no more than 50% of lid.
*Doors: 2 chains (24"), or 2 plates per vertical seam 2" by 6" by 1/4" plates. Drivers door unlimited except on fender side.
*Wheels: Aluminum may be changed to steel, no reinforcing.
*Tires: May be doubled or tubed no taller than 26"
*Engines: No protectors, may convert to carb (cut out hood enough to be safe), stock mounts. may run vertical headers out hood, SMALL ENGINE MOUNTED CARB PROTECTOR, 4" AWAY FROM HOOD, IF TOO LARGE YOU WILL REMOVE, THIS WILL NOT TURN INTO A KICKER!
*Suspension must remain completely stock, EXCEPT YOU MAY WELD A SMALL ANGLE IRON OR REBAR THE LENGTH OF THE TIE ROD AND YOU may weld A SLEEVE OVER THE STRUT TUBE, BUT STILL USING ALL STOCK COMPONENTS INCLUDING SHOCK ETC. 18" max HEIGHT to bottom of front bumper. NO AFTERMARKET TIE RODS OR SOLID STRUTS!
*Rear seat bar must run from door post to door post mid height of seat horizontally, may be contoured for room FOR DRIVER TO MOVE SEAT BACK. You may run a 4 point cage consisting of a dash bar, back bar and 2 door bars. 4" SQUARE OR ROUND max material, HALO BAR must come off rear seat bar, gas TANK protectors ok, MOUNTED off rear seat bar 6" off floor, tight to rear seat area. 30" wide ..PROTECTOR Can be taller than tank, but not excessive, OR ANGLED BACK OUT REAR WINDOW.
REAR WINDOW BAR FROM REAR ROOF TO 2 BOLTS ON TRUNK LID AND 2 BOLTS ON SPEAKER DECK USING 6X6 PLATES TO MOUNT, 3" MAXIMUM DIAMETER OF BAR.
May run halo bar off rear seat bar bolted to tin in 2 spots of roof in case of roll over.
*Gas tank ( steel only ) on floor behind driver or off rear seat bar centered in car. Chained, bolted or steel strap to secure not bungee cords. Use proper fuel hose, and clamps.
*Battery on passenger front secured to floor in steel or wood enclosure bolted to floor.
*Front bumper: May be swapped with 80 and newer full size steel, or any yr rear steel automotive bumper. If you cannot find steel bumper you may use tube steel up to 6" tall by 2" wide by 1/4" thick no wider than car, no pointy aftermarket BUMPERS. You may mount by bolting or welding. 3X3X 3\8" MATERIAL may extend INSIDE the frame UP TO THE core support ROD, CANNOT be pinned with threaded rod.
Stock style radiators only. No radi barrels. In stock location.
COMPACTS: WILL FOLLOW MIDSIZE RULES,
104.1 WHEELBASE OR LESS, 4cyl only, NO PACERS OR GREMLINS
MINI Vans:
* Engine:
4 or 6cyl. V8's allowed, and engine must be left stock. Can use headers up thru hood.
*4wd’s must remove front driveshaft.
* Doors:
Drivers door can be welded solid. All Other doors can have 2 chain or wire per door seam.
* Safety:
You can have a basic 4 point cage (seat bar, dash bar, and door bars) for drivers safety. A seat bar is mandatory. tubing can be up to 3” by 3” in diameter. You can have a gas tank protector ,no wider than 24'' wide and 6" off floor but must be attached to rear seat bar only.
* Tailgate and hatches:
Tailgate must remain vertical and in factory position or taken off. 2 chains or 2 wires, or 2 6"x3"x 1/4" plates per seam to secure lid.
* Tires
Doubled, skid steer, forklift or tractor tread tires are allowed. 31” max
height. You may use tubes in your tires, double tires ok. Remove all wheel weights before
inspection. Rims must be stock. No one piece home made rims allowed.
* Hoods:
Can have 4 chains or 4 threaded rods max. Only 2 threaded rods can go to frame in core support area. Threaded rod can be up to 1'' in diameter. Hood
plates for threaded rod can be 6”x6” max. you must have a 12" hole cut in hood incase of fire.
* Front Bumpers:
You may replace with 80 and newer steel, any year steel rear automotive or 6" tall by 2" deep by 1/4" flat steel bumper welded or bolted on.
* Rear bumper:
Must remain OEM or be taken off. No trailer hitches or brackets allowed. They must be completely removed before inspection.
* Frames:
No welding allowed anywhere on frame.
* Battery:
The battery must be relocated inside passenger side floorboard area of
Vehicle and securely mounted.
* Gas tank:
The gas tank must be in the front part of the box. Mini vans must have gas tank behind the driver’s seat. Gas tank and fuel lines must be securely mounted.
- These rules are meant to keep this class cheap and fun to compete in for Everybody.
Jim Falls located northeast of Eau Claire, Chippewa area of Wis.
Friday August 30TH @ 730pm
Classes:
Semi stock full size (replaces chain class) open to any year except no 74 and older Imperials, no 03 and newer automobiles, no suicide door Lincolns and no leaf sprung wagons.
Semi stock Midsize
Compact car class ***WILL FOLLOW MIDSIZE RULES UNLESS OTHERWISE NOTED***
Mini Vans
(MOVED TO SUNDAY),Youth midsize ages 13-19 using semi stock midsize rules...100% payback and trophy.(MOVED TO SUNDAY)
All classes $50 to enter,
***** Payouts: Back to the 90's $2000, 1500, 500, 250 ..$100 heat wins. Midsize: 800, 500, 250,.$1000 to win at 20 cars, Compacts: 700.00, 400, 200 one shot deal, mini vans 100% payback PLUS 500, BONUS ONCE WE HIT 20!
**Semi stock full size: This class is designed as a mainly oem class, Simple class with no gray areas. 1st rule is no aftermarket parts such as DP's, steel bell housings, Trans protectors, truck or after market trans cases, extreme cradles, etc., no stubbing, no frame swaps. no tilting.
****If its not in the rules you CANNOT do it!
**Preparation: All glass, lights, chrome, plastic, carpet, header panels, hubcaps, complete trailer hitches, gas tanks and debris etc must be removed.
**Safety: Helmets, eye protection, and protective clothing required! All air bags must be unbolted and removed, no cutting out just air bag.
**Gas tanks and battery (up to 2) automotive must be relocated. Gas tank on floor behind driver or centered behind driver on floor or off rear bar, battery box on front passenger floor area. Must not be used to strengthen car. Any gas tank protector must come off rear bar and be at least 6" off floor...can be tight to rear seat tin but no altering of tin in any way... NO WIDER THAN 30"
**Hoods and trunks : Hood (4)spots chains (36") or wire (4 loops) or rods to secure hood. If using rods, maximum is 3/4" in diameter and 2 must run through core support (4" max spacer)in front and 2 may run sheet metal to sheet metal only. Trunks 4 spots with 4 chains (30") 4 wires (4loops) or 2 rods, and 2 chains or wire. Rods must go through factory body mounts vertically in back, or welded to frame between mounts only. Hood, and trunk top plates not to exceed 6" by 6" square. Hood must be cut out for fires with maximum 4 bolts 3/8" per opening. Trunks may have 90 degree bend but must have 50% stock location. No bending down or wedging, simple 90 degree bend that's all. 2 chains in windshield opening to protect from hood. Tailgates 4 chains only 36" long, no threaded rods in tailgates of wagons.
**Body Forming: You may body form but no wedged trunks, 6" max dish.
**Doors : 2 spots per vertical seam 30" by 3/8 chain or 1 6 inch weld with 2" by 6" 1/4 plate max. drivers door may have unlimited.
**Safety cage. Basic 4 point with halo bar. Consists of dash bar above steering, 2 door bars mounted to dash and seat bars middle height area of door, 1 bar behind seat positioned midway height of seat horizontally. No bar larger than 6" in diameter, No plate to mount bars larger than 8" square. No kickers, just safety chain to sheet metal directly down from center of rear bar if only running rear bar. Halo bar off rear seat bar only, may be bolted to roof tin in 2 spots. Door bars may not go further back than 6" from center pillar or further forward than dash bar.
**Body bolts" May be replaced with up to 7/16" bolt max, body pucks may be removed. Washers no larger than 3" to be used. Do not get creative here.
**Transmission coolers are allowed but must be securely mounted and not do anything other than cool the trans. No trans protector, or steel or aluminum bells except contoured ultra, no steel tails, no aftermarket or truck trans cases, only stock mount or remove, stock cross members only, or 2x2 steel tube. May have aluminum ultra bell on previously broken trans and needed to be able reuse trans. Only mid plates are to change trans bolt pattern with no more than 1" wider.
**Engines: Vertical headers yes, Engine swaps yes, (VERY basic) engine cradle will be allowed with factory or after market frame mounts but must have rubber grommets. Pulley protector ok but must not at any time touch sway bar or instant DQ.
**Suspension: 15" minimum to lowest point of rear frame or bumper, 20" maximum to bottom of front bumper. You may use spring spacers, straps, bolting (1/2") bolts, or rod (3/4")max from lower a-arm to bottom of spring bucket to obtain this only, (2) 2"x6" straps per side must go directly down to spring bucket. 1 spot per side up
to 3/8" diameter by 30" chain can be used to hold in springs for rear end on sedans or wagons. No rods in rear shock area. (No reinforcing of suspension components). You may use watts conversion 1/4" or less or weld in pkg tray for 98-02s, and no more than 1" overlap for tray.
**Rear ends: Any factory rear end, can be reinforced with any size axle. No homemade rear ends and cannot reinforce car in any way. Pinion brake ok. Must use stock OEM control arms.
**Frames: No welding other than brackets for bumpers, or where specified in rules, you may dimple or notch rear frames.
**Bumpers of choice, may be reinforced. Substitute maybe be rectangular steel no wider than car, max 6" tall by 6" wide max up to 3/8" thick. Recommend welding stock chrome to make a factory appearing bumper. No filling aftermarket. You may hard nose but all shocks must be removed, Or shocks and brackets in factory position may be welded with single pass, no front and rear bracket swaps. No welding further back than 8" from center of core support hole.
I will allow 2 spots per bumper of wire or chain. May go to core support or frame only not around threaded rod or hood. Nothing excessive or you will remove it all. 5 3/8" fender bolts allowed per fender.
**Steering...aftermarket or homemade steering.. After market brakes and shifting components are fine, just do not reinforce car in any way with these components.
**Tires of choice up to 30" tall, valve stem protectors ok.. Any wheel that started as a factory wheel, no bead locks.
ONLY AFTER MARKET PARTS** gas pedal, steering , transmission or floor mounted shifter nothing hanging down near cross member, dash or bar mounted brake unit or plate for manual brakes..basic engine cradle..aluminum factory type radiator in factory position, and slider drive shafts.
****80 and newer metric cars will be allowed a (1) per side 3/8" 18x4" rear hump plate centered on rear hump.
****Gas tank protectors will allowed off rear seat bar only, no wider than 30" by 4" at the rear seat area, they may touch but do not alter floor to make tighter or you will be loaded, must be 8" off floor.
****rear window bars will be allowed, no more than 4" in diameter, bolted or welded to roof, and bolted only with 2 bolts in speaker deck and 2 bolts in trunk lid.
Semi stock midsize:
Mid-Size 4-Cyl. And 6-Cyl.,8-Cly ONLY, no full framed cars. No wheel base over 113"
Cars must have all airbags and charges removed by unbolting not cutting out just air bags. You must remove all glass and carpet, headliner, in addition to flammable materials though dash may remain intact . All mirrors, chrome, plastic, fiberglass header panels, factory gas tank , hitches must be removed.
*Hoods and trunks: 4 Spots Maximum in each...Choice 4 chains (24"), 4 spots wire (4 loops) maximum, or combination of 2 3/4" threaded rod at core support area only with 2 chains or wire. Trunk choices 4 chains, wires, or plates (6x2x1/4") or 2 3/4" rods and 2 chains, 2 plates (2x6x1/4") or wire... 12" round or square hole cut in hood in case of fire. All hood and trunk hold down plates to not exceed 6x6x 1/4”, __ body forming allowed just do not over do it...4" dish in trunk lid max__, but you will be allowed 1 90 degree bend in trunk lid. no more than 50% of lid.
*Doors: 2 chains (24"), or 2 plates per vertical seam 2" by 6" by 1/4" plates. Drivers door unlimited except on fender side.
*Wheels: Aluminum may be changed to steel, no reinforcing.
*Tires: May be doubled or tubed no taller than 26"
*Engines: No protectors, may convert to carb (cut out hood enough to be safe), stock mounts. may run vertical headers out hood, SMALL ENGINE MOUNTED CARB PROTECTOR, 4" AWAY FROM HOOD, IF TOO LARGE YOU WILL REMOVE, THIS WILL NOT TURN INTO A KICKER!
*Suspension must remain completely stock, EXCEPT YOU MAY WELD A SMALL ANGLE IRON OR REBAR THE LENGTH OF THE TIE ROD AND YOU may weld A SLEEVE OVER THE STRUT TUBE, BUT STILL USING ALL STOCK COMPONENTS INCLUDING SHOCK ETC. 18" max HEIGHT to bottom of front bumper. NO AFTERMARKET TIE RODS OR SOLID STRUTS!
*Rear seat bar must run from door post to door post mid height of seat horizontally, may be contoured for room FOR DRIVER TO MOVE SEAT BACK. You may run a 4 point cage consisting of a dash bar, back bar and 2 door bars. 4" SQUARE OR ROUND max material, HALO BAR must come off rear seat bar, gas TANK protectors ok, MOUNTED off rear seat bar 6" off floor, tight to rear seat area. 30" wide ..PROTECTOR Can be taller than tank, but not excessive, OR ANGLED BACK OUT REAR WINDOW.
REAR WINDOW BAR FROM REAR ROOF TO 2 BOLTS ON TRUNK LID AND 2 BOLTS ON SPEAKER DECK USING 6X6 PLATES TO MOUNT, 3" MAXIMUM DIAMETER OF BAR.
May run halo bar off rear seat bar bolted to tin in 2 spots of roof in case of roll over.
*Gas tank ( steel only ) on floor behind driver or off rear seat bar centered in car. Chained, bolted or steel strap to secure not bungee cords. Use proper fuel hose, and clamps.
*Battery on passenger front secured to floor in steel or wood enclosure bolted to floor.
*Front bumper: May be swapped with 80 and newer full size steel, or any yr rear steel automotive bumper. If you cannot find steel bumper you may use tube steel up to 6" tall by 2" wide by 1/4" thick no wider than car, no pointy aftermarket BUMPERS. You may mount by bolting or welding. 3X3X 3\8" MATERIAL may extend INSIDE the frame UP TO THE core support ROD, CANNOT be pinned with threaded rod.
Stock style radiators only. No radi barrels. In stock location.
COMPACTS: WILL FOLLOW MIDSIZE RULES,
104.1 WHEELBASE OR LESS, 4cyl only, NO PACERS OR GREMLINS
MINI Vans:
* Engine:
4 or 6cyl. V8's allowed, and engine must be left stock. Can use headers up thru hood.
*4wd’s must remove front driveshaft.
* Doors:
Drivers door can be welded solid. All Other doors can have 2 chain or wire per door seam.
* Safety:
You can have a basic 4 point cage (seat bar, dash bar, and door bars) for drivers safety. A seat bar is mandatory. tubing can be up to 3” by 3” in diameter. You can have a gas tank protector ,no wider than 24'' wide and 6" off floor but must be attached to rear seat bar only.
* Tailgate and hatches:
Tailgate must remain vertical and in factory position or taken off. 2 chains or 2 wires, or 2 6"x3"x 1/4" plates per seam to secure lid.
* Tires
Doubled, skid steer, forklift or tractor tread tires are allowed. 31” max
height. You may use tubes in your tires, double tires ok. Remove all wheel weights before
inspection. Rims must be stock. No one piece home made rims allowed.
* Hoods:
Can have 4 chains or 4 threaded rods max. Only 2 threaded rods can go to frame in core support area. Threaded rod can be up to 1'' in diameter. Hood
plates for threaded rod can be 6”x6” max. you must have a 12" hole cut in hood incase of fire.
* Front Bumpers:
You may replace with 80 and newer steel, any year steel rear automotive or 6" tall by 2" deep by 1/4" flat steel bumper welded or bolted on.
* Rear bumper:
Must remain OEM or be taken off. No trailer hitches or brackets allowed. They must be completely removed before inspection.
* Frames:
No welding allowed anywhere on frame.
* Battery:
The battery must be relocated inside passenger side floorboard area of
Vehicle and securely mounted.
* Gas tank:
The gas tank must be in the front part of the box. Mini vans must have gas tank behind the driver’s seat. Gas tank and fuel lines must be securely mounted.
- These rules are meant to keep this class cheap and fun to compete in for Everybody.
