|
Post by bubba89x on Feb 5, 2013 20:31:23 GMT -5
I've never seen them bend behind the a arms
|
|
|
Post by redneckracing12 on Feb 5, 2013 21:23:54 GMT -5
dont forget to incorporate the sway bar into your build on the 98-02
|
|
|
Post by bubba89x on Feb 5, 2013 22:20:52 GMT -5
Use the stock sway bar turn it up side down cut the end off so it fits the frame rails and if u can weld it to the bottom frame rails
|
|
|
Post by redneckracing12 on Feb 5, 2013 22:46:36 GMT -5
Use the stock sway bar turn it up side down cut the end off so it fits the frame rails and if u can weld it to the bottom frame rails I was talking about using it in a similar manor as stock configuration but modified slightly, just look at it for a bit and you will see.
|
|
|
Post by D1dunaway on Feb 7, 2013 21:04:06 GMT -5
Will a 92 bubble fit right on a 2000 marquis frame??
|
|
|
Post by onlyone on Feb 7, 2013 21:30:53 GMT -5
Yea
|
|
|
Post by D1dunaway on Feb 7, 2013 21:35:45 GMT -5
Thanks
|
|
|
Post by derby111 on Feb 8, 2013 9:49:03 GMT -5
Will square trunk lids and hoods work on these? I have an 01 with aluminum hood and trunk lid but I don't have access to anymore 98^
|
|
Jon
Heat Winner
Posts: 591
|
Post by Jon on Feb 8, 2013 10:07:40 GMT -5
a square vic hood will fit on a 98-02 hood with a little trimming to the sides mostly near the front and will not hang over the core support mor then an inch
|
|
|
Post by chevyguy82 on Feb 8, 2013 19:59:07 GMT -5
My fords seem to keep bending behind the crush box. It takes a while to bend but thats where everyone of them bends. I usually tilt at the box till they are level. Im not using a pulley protector or dp maybe thats why. Just kinda wondering if Im missing something.
|
|
|
Post by ajb729 on Feb 8, 2013 20:18:47 GMT -5
What's most of u Tilting these too? Have seen some 8 inches and some only 4 inches, just didn't know if it mattered if u went more or just a little bit
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 8, 2013 20:38:00 GMT -5
What's most of u Tilting these too? Have seen some 8 inches and some only 4 inches, just didn't know if it mattered if u went more or just a little bit Where are you tilting it? Boxes or crossmember?
|
|
|
Post by ajb729 on Feb 8, 2013 20:41:01 GMT -5
Boxes
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 8, 2013 20:46:35 GMT -5
When I build mine, I'm gonna go 5 at the boxes. Itd be a 96 body on a 98-02 frame though.
|
|
lincoln
Feature Winner
Posts: 3,176
|
Post by lincoln on Feb 8, 2013 21:00:21 GMT -5
What's most of u Tilting these too? Have seen some 8 inches and some only 4 inches, just didn't know if it mattered if u went more or just a little bit It all depends where you set your azz. The lower you set your azz the more you have to pitch it to get it level.
|
|