|
Post by smashford on Jun 25, 2019 19:03:19 GMT -5
If running alternator you will need the regulator,
|
|
|
Post by fillthyanimal75 on Jul 9, 2019 19:00:37 GMT -5
Can you cold bend these and if so where do you bend them?
|
|
n8
Feature Winner
Posts: 1,147
|
Post by n8 on Jul 10, 2019 7:20:47 GMT -5
Can you cold bend these and if so where do you bend them? Yes. I bend them at the crush box.
|
|
|
Post by tdawgmiller64 on Jul 13, 2019 17:37:58 GMT -5
What is everyones preferred motor/trans combo for a 98 Vic
|
|
|
Post by cheezwhiz31 on Jul 14, 2019 19:18:23 GMT -5
355 small block Chevy and 400th long tail trans
|
|
|
Post by rennyx on Jul 14, 2019 20:23:52 GMT -5
I am allowed to reinforce tie rods but they must start as stock with only metal added. Any suggestions appreciated.
|
|
|
Post by derbykid91 on Jul 14, 2019 22:52:13 GMT -5
I have a few questions about prepping a 89 merc grand marquis. What is the best fuel setup battery wiring and best way to ensure the rear packs in and up
|
|
|
Post by derbykid91 on Jul 14, 2019 22:54:36 GMT -5
I have a few questions about prepping a 89 merc grand marquis. What is the best fuel setup battery wiring and best way to ensure the rear packs in and up
|
|
|
Post by rhull1977 on Jul 17, 2019 8:37:46 GMT -5
I am allowed to reinforce tie rods but they must start as stock with only metal added. Any suggestions appreciated. 97 to 2001 f150 tie rods.
|
|
|
Post by rennyx on Jul 18, 2019 16:25:21 GMT -5
Will they fit into box vic spindles? How do you reinforce or are they fine in stock form?
|
|
|
Post by rhull1977 on Jul 18, 2019 16:36:25 GMT -5
Will they fit into box vic spindles? How do you reinforce or are they fine in stock form? Look at a set you will see why I suggest them. The fit but you can ream the spindle and drag link to seat them deeper. I've personally never broke one stock and had the upper a arm broke off.
|
|
|
Post by roughneck06 on Jul 19, 2019 9:39:23 GMT -5
Do the 80s town cars come hd?? I was told only the vics. But looking at the package tray on a 81 and 87 they both are stamped HD. Just curious
|
|
|
Post by cheezwhiz31 on Jul 19, 2019 17:35:09 GMT -5
Do the 80s town cars come hd?? I was told only the vics. But looking at the package tray on a 81 and 87 they both are stamped HD. Just curious i've never seen one. what is the stamp behind the passenger rear tire on the out side of the frame say? STD or HD? also do the upper a-arm rods have grease zerks on the ends of them?
|
|
|
Post by rennyx on Jul 20, 2019 13:28:05 GMT -5
For the f150 tie rods would I need ones for a two or four wheel drive? They both look to be different so I am not sure if they are the same length.
|
|
|
Post by rhull1977 on Jul 20, 2019 20:53:38 GMT -5
I run 2wd ones. Plenty of adjustment. Did you see why I say run them.
|
|