2022 Fall Pumpkin Brawl Roberts, WI October 22, 2022

[gbr12]

2022 Roberts Fall Pumpkin Brawl Demolition Derby

Saturday, October 22, 2022
1:00 PM Start time
(In case of bad weather the derby will be moved to Sunday, same time as listed above.)

Inspection starts at 8 AM. ALL vehicles MUST have passed tech and be ready to go by 12:30.
Drivers Meeting will begin at 12:45 sharp.
ALL drivers must attend meeting before the show.
(Note: For drivers and drivers only, not pit members. If you believe a rule has been broken or a competitor got through tech with an infraction, or something was added after inspection, this will be your time to bring it up, after that, nothing else is to be said.)

This will be a “clean up show,” but fresh cars will be permitted. That being said, We will do our best to put cars in there respective classes.

We WILL be having powerwheels. Please have the kids ready and in there powerwheels by 12:15. Powerwheels can be dropped off at back gate, anytime before 12 Noon.

ENTRY / PIT / DRIVER RULES AND INFO
8 classes:

Registration Fees and Payouts are listed below for the Fall Pumpkin Brawl

Registration:

$40 Lawnmowers

$75 Midsize Chain, Mid Size Semi Weld, Minivan/SUV(singles)

$100 Full Size Limited Weld, 2 Man Extreme Minivan/SUV, Midsize Firewall Forward, Run What Ya Brung(All cars must have ran earlier in the day. Midsize mods will be allowed to run in.)

Payouts:

Full Size Limited Weld:
$1000, $600, $300

Compact/Midsize Semi Weld:
$800, $450, $250

Compact/Midsize Chain:
$800, $450, $250

Minivan/SUV:
$800, $450, $250

2 Man Extreme Minivan/SUV:
$900, $500, $300

Lawnmowers:
100% payback from registration fees.

Midsize Firewall Forward:
100% payback from registration fees.

Run What Ya Brung (Clean Up Class):
100% payback from registration fees.

***Payouts based on a minimum of 10 cars per class. Payouts will be adjusted if less then 10 cars!!!***

We WILL be running heats with higher car counts, so plan to bring extra parts and tools. Promoters discretion will be advised.

Entry fee covers the vehicle and driver ONLY.
$50 LATE FEE for drivers that show up after 12:15PM

Admission Prices: (includes stands & pits)

Adults: $15
Children: $5 (12 and under)

Must be 16 years of age or older to drive in the derby.
ID required – ANY driver may be asked for ID.

ANY VEHICLE THAT WE BELIEVE TO BE UNSAFE, WILL NOT RUN!!!

Call Matt Skoglund 715-410-1429 with any general derby questions.
Call Tim “HOLLYWOOD” Myer 507-421-1521 or Justin Polen 715-760-1311 with any tech questions.

[gbr12]

I will post rules for other classes in the near future. Being Roberts is a Fall “cleanup” show, there are many builds from different promoters that will be crammed into one show so have to get them right. Thanks!!!

715 Motorsports & Promotions
Entry fee: $40

***Lawn Mower Class***

Any mower or driver that is unsafe will be disqualified. In all matters, judges’ decisions are final.

All drivers must remain on mowers during competition, except under red flag or rollovers. No getting off the mower to get unstuck or to work on the engine. Must operate from the seat.

Seat belts are not allowed due to the possibility of rollovers. 2 rollovers allowed, 3rd is disqualification.

Drivers must wear approved safety helmets.

Numbers must be minimum of 5”, visible on both sides.

Must make a hit once every minute.

SPECIFICATIONS:
1: Any front engine riding lawn mower allowed. (No rear engine riders or zero turns allowed.)

2: All mowers may be belt or shaft driven in the final drive.

3: No homemade mowers permitted.

4: All common makes of GAS lawn mower engines may be used. No engines not originally designed for a lawn
mower can be used. No diesels or engines with more than two cylinders. May be electric or recoil start.

5: Engines shall not exceed 25 rated factory horsepower.

6: No sparkplug guards or motor guards allowed.

7: Pulleys may be changed to your designed gearing. Nothing over 10 mph. Must pre-set the speed prior to event.

8: Leg guards, all mowers must be equipped with strong leg guards. They must protect the driver’s legs and feet at
all times. Leg guards should cover the area by the driver’s feet. Leg guards should NOT protect the tires in any way. No limit on the strength of materials, but size requirements are to be within the tires, cannot cover the tires, and must be mounted in line with the outsides of the tires. Must be enclosed, utilizing plate steel or expanded steel. Leg guards can be connected to the seat guard to provide support. Foam is recommended on top of leg guards.

9: Seat Guards can be mounted on the rear fenders and/or off the bumper, and can be tied in with the leg guards, but should not cover the rear fenders completely. (Leave some fender to get bent.) The back seat guard should be fully plated, or expanded steel behind the seat, to be protected from the corners of the hoods. No height restriction above the seat, this acts as the roll bar.

10: Headers: may make homemade exhaust but it must “generally” point up or down.

11: All types of factory mufflers may be used.

12: Bumpers: Front bumpers may only exceed no more than 18” past the grill or hood. May be made of channel,
square, round, flat, angle iron, not exceeding 4” in size. Top of front bumpers must be placed at frame level, not exceeding height of the front tires. Rear bumper bracket may be attached all the way up to the leg guards. Bumpers must be no wider than the inside of all the tires, front and back. “C” channel or angel iron must be mounted facing the frame, with sharp edge toward the machine front and back.

13: Hood: Must have a minimum of one hold (bolt or chain) down by the steering wheel and a maximum of four. May weld pipe or threaded rod (1 inch max) off the frame up to the hood for support. Hood washer is 4” maximum. Cannot connect hood bolts from front to back, only side to side. (This will allow the hood to bend.) Cut threaded rod flush with hood for safety.

14: Tires: must be from lawn mowers, snow blowers, tillers, or small trailer tires, no car tires. Tires may be tubed or slimed. No foamed or solid tires. no valve stem protection allowed.

Please contact Tim “Hollywood” Myer with any questions at 507-421-1521 or on Facebook at 715 Motorsports & Promotions