|
Post by younggun202 on Dec 2, 2019 1:22:25 GMT -5
Is there specific years fords came with gussets? Or specific models? I’ve ran couple square fords some gussets and some aren’t. Any help would be great thanks!
|
|
|
Post by cheezwhiz31 on Dec 2, 2019 10:38:53 GMT -5
90-91 Vic and merc are square and gusset 92-97 merc and vic are bubble and gusset. 98-02 are bubble and watts rear and gusset.
90 lincoln are bubble and gusset and square stamped upper a-arms
91-97 are bubble and gusset and wishbone upper a-arm
|
|
|
Post by beardo22 on Dec 5, 2019 0:12:03 GMT -5
Good to know. How about the front frame horns. Some are "big horn" some are not? My 96,97 and 99 all looked the same up front with internal plates in the front. All p71s too.
|
|
|
Post by cheezwhiz31 on Dec 5, 2019 9:15:03 GMT -5
Good to know. How about the front frame horns. Some are "big horn" some are not? My 96,97 and 99 all looked the same up front with internal plates in the front. All p71s too. Your not looking close enough if you think those years all look the same... Internal plates started in 90 and go all the way up to 02 Lincoln's and some mercs have a little extra in them if you look close. Over all size and some changes with seam welds and design changed in 98 to 02 Some 97 came with the 98 style front with the 4 link control arm style arms. P71 or not they will have the internal plates up front from 90 to 02. P72 are hot right now too...
|
|
jb3c
Future Icon
Posts: 10
|
Post by jb3c on Dec 14, 2019 21:00:05 GMT -5
So in a perfect world a 97 Lincoln would be the thing to have
|
|
|
Post by cheezwhiz31 on Dec 16, 2019 10:47:06 GMT -5
All depends on what rules you are building for. But yes a good/hair better then some.
|
|
jb3c
Future Icon
Posts: 10
|
Post by jb3c on Dec 16, 2019 15:56:12 GMT -5
Allowed 4 down bars inside the car down the the frame, can tilt at crossmember, can switch watts, hard nose, any drive train, and rear, 2x2 crossmember, can switch a arms and spindles, allowed aftermarket tie rods, can replace ball joints with factory ball joint. Can shorten frame to rad support mount, allowed gas tank protector and 2 4x6 1/4 plates where ya want.
|
|
demoboy333
Feature Winner
Enter your message here...
Posts: 3,124
|
Post by demoboy333 on Dec 16, 2019 18:43:08 GMT -5
Allowed 4 down bars inside the car down the the frame, can tilt at crossmember, can switch watts, hard nose, any drive train, and rear, 2x2 crossmember, can switch a arms and spindles, allowed aftermarket tie rods, can replace ball joints with factory ball joint. Can shorten frame to rad support mount, allowed gas tank protector and 2 4x6 1/4 plates where ya want. I'd go 98 to 02. Unless your allowed 03 ups.
|
|
jb3c
Future Icon
Posts: 10
|
Post by jb3c on Dec 16, 2019 18:50:44 GMT -5
We can but only thing can do is change gear box
|
|
jb3c
Future Icon
Posts: 10
|
Post by jb3c on Dec 16, 2019 19:22:55 GMT -5
And no dp
|
|
|
Post by cheezwhiz31 on Dec 16, 2019 23:13:15 GMT -5
98 to 02 for sure
|
|
jb3c
Future Icon
Posts: 10
|
Post by jb3c on Dec 17, 2019 7:52:37 GMT -5
I’ve never messed with an 03, the suspension and aluminum cradle scares me. Only thing can change ya steering box.
|
|
|
Post by cheezwhiz31 on Dec 17, 2019 9:07:50 GMT -5
trans protector or steel bell and tail??
|
|
jb3c
Future Icon
Posts: 10
|
Post by jb3c on Dec 17, 2019 9:25:54 GMT -5
Yes we can have all that, just no DP. Can have lower cradle, from plate, pp. but if run pulls protector have to cut sway bar
|
|
|
Post by cheezwhiz31 on Dec 18, 2019 8:59:16 GMT -5
Yes we can have all that, just no DP. Can have lower cradle, from plate, pp. but if run pulls protector have to cut sway bar should be able to build yourself a nice hard 98-02 with them rules and build...
|
|