April 29 2017 Carrollton Team show has been CANCELLED..

[KING]

All Team Classes are 300.00 entry per team and pre registration is mandatory.
Mail entries to 1236 lincoln ave nw Carrollton Ohio 44615

3 man mild weld full size class any year car no imps .. 8000.00 PURSE

3 man pro compact class NO V8 CARS .. 7500.00 PURSE

3 man full size trucks .. 3000.00 PURSE

NON TEAM CLASSES ARE 50.00 entry and 100% PAYOUT

mild weld compact class

youth class

stock build mini trucks if we can get 10 pre paid by march 1st

power wheels class 10.00 entry the kids will have a full hour of track time.....


Details are on the facebook page Mangled Metal Productions

[demodave216]

Holy Fu@k the King is back?

[lorco28]

Is the full size team event 80s and newer or any year?

[CHUNKY MONKEY 13]

Compact rules? Lol

[just a wannabe]

PRO COMPACT RULES .. 3 MAN TEAM SHOW 7500.00 PURSE..
ENTRY= 300.00 PER TEAM

All cars must remain stock unless otherwise noted. If it is not in the rules, it does not mean you can do it. So Don’t!
**CAR TYPE any FWD car or station wagon that has a wheelbase of 109" and under with a 4 or 6 cylinder engine. RWD CARS 106" WHEELBASE..
**Stripping: All outside hardware such as glass, plastic, fiberglass and chrome molding, door handles, mirrors etc must be removed prior to arrival. No broken windows in doors. All flammable materials must be removed such as carpets, upholstery, headliners, and back seats. Cars must be clean and free of loose objects inside and in the trunk area including spare tire, rims and parts. Insulation blanket under the hood must be removed. All items must be removed except for front seat and dash..
**Body: Tucking and wedging and creasing allowed. Wheel wells may be cut and rolled for tire clearance. 5 bolts in each wheel lip acceptable 3/8 bolts and 1" washers max size
**SUSPENSION: no leaf conversions, factory leaf cars must have factory leafed packs and clamps only. No solid shackles. Coil springs may be wired or welded into place. Struts and shocks may be homemade but must be stock in size. Tie rods may be reinforced. 2 inch square tubing or plate can be welded from lower A arm to frame for front bumper height requirements. No hump plates and rear end can be chained to humps.
**FRAME: factory stock, you can notch and pre bend
. **Engine :You may swap motors/transmissions No V-8 you can chain engine down in 4 spots.engine cradles, pulley protectors and motor plates are allowed.
**Transmission: Floor shifters allowed. burp tube must be installed over the dipstick and routed to the ground to prevent fires Transmission may be secured by chain , # 9 wires or stock mount
**Rear End: Any 5 bolt pattern accepted ~ spiders can be welded ~ .. Any drive shaft allowed.
-**Bumpers: Any automotive bumper can be used. Loaded bumpers are allowed No homemade pointy bumpers. 10 inch bumper shocks and Your choice of round or square tubing.. or 3 inch wide ¼ inch strapping on outside frame 10“back from bumper.. #9 wire in 2 places around core support to bumper. 2 strands per hole max.~ You may trim bumper ends~ maximum front and rear bumper height 24 '' and rear bumper a minimum of 16 ''. Measurement will be taken from ground to center of bumper...
**Tires and Rims: doubled, glued, and screwed tires allowed. Valve stem guards allowed.. No studded tires on drive tires. No restriction on tread pattern or tire ply ratings. REMOVE ALL WHEEL WEIGHTS BEFORE INSPECTION. Solid rims and bead lock rims are allowed.
**Exhaust System: Headers can exit straight up through the hood. If exhaust system runs under the car, it must exit under the front doors.
**Steering Column: may be swapped, aftermarket steering shafts allowed
**Fuel: Gasoline only! 8 gallons max. per heat and NO PLASTIC gas tanks PERIOD.
**Fuel Tank: Original gas tanks Must be removed unless they are mounted in front of the rear axle. Tanks are to be mounted behind driver. They Must be mounted properly and all connections must be secured and leak proof. 5 gallons max. 5 holes must be in floor around fuel tank to prevent pudling of spilled fuel.. (If it moves 1/8 inch ~ it’s NOT considered secure) all fuel tanks must be covered with a non flammable material .
**Fuel Line: Electric fuel pumps are acceptable. Must have shut off switch within drivers reach. Mounted on the rear roll cage bar. Must be 12 '' from the passenger side door with off position being down. Clearly marked for safety personal.
**Roll Cage: One bar mandatory behind driver seat. 12x12x ¼ max end plates welded on body for cage. No further back then 12 inches behind door post. DASH BARS AND DOOR BARS ARE OPTIONAL FOR DRIVER SAFETY ONLY. bars can be up to 4 '' max diameter. Roll over bar allowed!! 2 down legs can be straight down from back seat bar to floor welded to sheet metal only.
TANK PROTECTORS...24" WIDE and can be tight to the rear sheet metal in back seat area. no down bars to body. 2 bars can go up to rollover bar off the backside of protector.
**Body Mounts: Can be changed to 5/8 bolts 3 inch washers solid to body.
**Doors: ALL doors may be welded solid by using 3'' wide max, ¼ thick strap on all door seams. . One ¼ plate not to exceed drivers door by 6 inches, may be welded on drivers door for safety! if not choosing to weld all other doors may be banded chained or wired in 8 spots on each door . bottoms each door can have 2 spots wrap around the frame . Any door that comes open during heat or feature will automatically be disqualified.
. NUMBERS MUST BE ON A ROOF SIGN . Signs need to be at least 20x20.
**Hoods: Fiberglass hoods may be changed. Hoods can be bolted together at cut out. 10- 3/8 bolts max.. with 1 '' dia washers . No welding. HOOD CAN BE SECURED IN 6 SPOTS. By using 1 inch bolts and 4 '' washers max. if using wire you can weld washers on hood 8 spots ,4 strands per hole . Must have 14 '' hole in center if not using headers. HOODS MUST BE OPEN FOR INSPECTION
**TRUNKS .. can be welded solid with 3 inch wide by ¼ thick strapping. Speaker deck may be removed. quarters must remain upright trunks can be tucked and creasing allowed
12" inspection hole must be in the trunk for inspection. 10 3/8 bolts 1" washers around cut out only.
*Radiator & Fans: Any stock automotive allowed. Only in stock position. Secured by 9# wire, nylon straps, 2 places only. Remember Water only! No coolant. Electric fans permitted.
**Battery: 2 batteries of any size. Must be placed in a secure position in the front. passenger side floor board. Battery box is suggested, which must be securely fastened down. Battery Must be covered.
**STARTING METHOD : you may use toggle, push button or hot wiring method
**Brakes: Brakes MUST be functional.
** CORE Support: 1 inch all thread can be used from frame up through core support and can be used as two hood bolts
Windshield area.... 2 pieces of rebar,3" plate or 9 wire can go from roof to cowl panel.
Back window..... 1 bar from roof straight down to factory trunk seam/speaker deck area. 4x4 plates max welded to sheet metal to weld the bar to. This is not intended to be a kicker.

[just a wannabe]

2017 MILD WELD COMPACT CLASS RULES. Non team event ........... entry is 50.00 100% payback

.
**Car type: any FWD car or station wagon that has a wheelbase of 109" and under with a 4 or 6 cylinder engine. RWD CARS 106" WHEELBASE..
**Stripping: All outside hardware such as glass, plastic, fiberglass and chrome molding, door handles, mirrors etc must be removed prior to arrival. No broken windows in doors. All flammable materials must be removed such as carpets, upholstery, headliners, and back seats. Cars must be clean and free of loose objects inside and in the trunk area including spare tire, rims and parts. Insulation blanket under the hood must be removed. All items must be removed except for front seat and dash..
**Body: Tucking and wedging is not allowed. All sheet metal must remain factory stock.
Wheel wells may be cut and rolled for tire clearance. 5 bolts in each wheel lip acceptable 3/8 bolts and 1" washers max size
**Suspension: factory stock factory leaf cars must have no more than 4 springs per side 2" stagger and 4 clamps per car.
**FRAME: factory stock, you can notch and pre bend. No cradle swaps
. **Engine :You may swap motors/transmissions
**Transmission: Stock shifters ONLY burp tube must be installed over the dipstick and routed to the ground to prevent fires Transmission may be secured by chain , # 9 wires or stock mount
**Rear End: Any 5 bolt pattern accepted ~ spiders can be welded ~ .. Any drive shaft allowed.
-**Bumpers: Any automotive bumper can be used. You must weld or bolt the bumper to the shock . bolts can be up to 1/2 dia in the factory location.,.You can weld the bumper shock to the frame. Two passes on the shock two passes on the frame. #9 wire in 4 places around core support to bumper. 2 strands per hole max.~ You may trim bumper ends~ maximum front and rear bumper height 24 '' and rear bumper a minimum of 16 ''. Measurement will be taken from ground to center of bumper...
**Tires and Rims: doubled, glued, and screwed tires allowed. Valve stem guards allowed.. No studded tires on drive tires. . No restriction on tread pattern or tire ply ratings. REMOVE ALL WHEEL WEIGHTS BEFORE INSPECTION. No solid rims or bead locks.
**Exhaust System: Headers can exit straight up through the hood. If exhaust system runs under the car, it must exit under the front doors.
**Steering Column: may be swapped, aftermarket steering shafts allowed
AIR BAGS MUST BE REMOVED
**Fuel: Gasoline only!
**Fuel Tank: No plastic tanks..No stock tanks mounted inside the car.
Original gas tanks Must be removed unless they are mounted in front of the rear axle. Tanks are to be mounted behind driver. They Must be mounted properly and all connections must be secured and leak proof. 5 gallons max. 5 holes must be in floor around fuel tank to prevent puddling of spilled fuel.. (If it moves 1/8 inch ~ it’s NOT considered secure) all fuel tanks must be covered with a non flammable material .
**Fuel Line: Electric fuel pumps are acceptable. Must have shut off switch within drivers reach. Mounted on the rear roll cage bar. Must be 12 '' from the passenger side door with off position being down. Clearly marked for safety personal.
**Roll Cage:One bar mandatory behind driver seat. 8x8x ¼ max plates welded on body for cage. No further back then 12 inches behind door post. DASH BARS AND DOOR BARS ARE OPTIONAL FOR DRIVER SAFETY ONLY. bars can be up to 4 '' max diameter. Roll over bar allowed!!
TANK PROTECTORS...24" WIDE and can be tight to the rear sheet metal in back seat area. no down bars to body. 2 bars can go up to rollover bar off the backside of protector.
**Body Mounts. factory stock
**Doors: Drivers Door may be welded solid by using 3'' wide max, ¼ thick strap on all door seams. . One ¼ plate not to exceed drivers door by 6 inches, may be welded on drivers door for safety! all other doors may be banded chained or wired in 8 spots on each door . Bottoms of each door can have 2 spots wrap around the frame . Any door that comes open during heat or feature will automatically be disqualified.
. NUMBERS MUST BE ON A ROOF SIGN . Signs need to be at least 20x20.
**Hoods: Fiberglass hoods may be changed. Hoods can be bolted together at cut out. 10- 3/8 bolts max.. with 1 '' dia washers . No welding. HOOD CAN BE SECURED IN 6 SPOTS by wire , chains or banding. if using wire you can weld washers on hood 6 spots ,4 strands per hole . Must have 14 '' hole in center if not using headers. HOODS MUST BE OPEN FOR INSPECTION
**Trunks .. Can be secured with wire chain or banding. In 8 spots. 12" inspection hole must be in the trunk if it can’t be opened for inspection. 10 3/8 bolts 1" washers around cut out only.
*Radiator & Fans: Any stock automotive allowed. Only in stock position. Secured by 9# wire, nylon straps, or bungee straps in 2 places only. Remember Water only! No coolant. Electric fans permitted.
**Battery: 1 battery of any size. Must be placed in a secure position in the front. passenger side floor board. Battery box is suggested, which must be securely fastened down. Battery Must be covered.
**Starting method : you may use toggle, push button or hot wiring method
**Brakes: Brakes MUST be functional.
** Front Windshield Area: two pieces of rebar, chain, #9 wire or 3 inch strapping can be mounted from roof to cowl panel to prevent decapitation. Nothing in the rear window in this class.

[39x]

How's entry's looking?

[demodave216]

Feb 8, 2017 19:37:17 GMT -5 39x said:

How's entry's looking?

Rob your better off checking his FB page, or calling him. I think he stops by here once in awhile, but he's always on his phone. He told me the other day he has 15 big cars signed up so far. I've been trying to talk him into adding a promod heat, but he just laughs at me

[39x]

Cool. Thanks Dave

[dcderbyteam]

Truck rules?

[lawrence70]

Are there enuff entries for mini trucks

[19dh]

I just heard he canceled