wickedridesinc
Feature Winner
https://wickedderby.webconnex.com/UDregistration
Posts: 1,281
|
Post by wickedridesinc on Jan 5, 2016 1:07:01 GMT -5
This show is being broke into 2 days, so if you don't see your class listed below it maybe listed for the July 16th schedule of events. see link below we-crash.proboards.com/thread/61217/10-000-proctorville-july-16thWhen: July 9th 2016 Where: Proctorville, OH Contacts 812-454-4520 Brandon (event info) 304-654-2994 (fair info) SEND ENTRIES TO: LAWRENCE COUNTY AGRICULTURAL SOCIETY PO BOX 610 IRONTON OH 45638 MONEY ORDERS ONLYEntry form REGISTRATION FORM 2016.docx (35.14 KB)Below is a tentative class schedule and list of payouts, some editing maybe required. They will be finalized as we get closer to the event. Compact Class (30 max)1st $2500 2nd $1000 3rd $500 Maddog $500 $50 entry fee Mini Trucks (30 max)1st $1000 2nd $500 3rd $250 Maddog $500 $50 entry fee Windshield Class (30 max)1st $2500 2nd $1000 3rd $500 Maddog $500 $50 entry fee Mowers (stock)100% payback $25 entry fee Mowers (modified)100% payback $25 entry fee Power Wheelstrophy to all Pre Registered Free
|
|
wickedridesinc
Feature Winner
https://wickedderby.webconnex.com/UDregistration
Posts: 1,281
|
Post by wickedridesinc on Jan 5, 2016 1:07:13 GMT -5
Compact rules.
AUTOMOBILE BODY REGULATIONS- ALL JUDGES DECISIONS ARE FINAL
Only 50% of your car can be painted black! NO ALL BLACK CARS!
1.front wheel drive 108" wheelbase, rear wheel drive 106" wheelbase NO V8s NO FULL FRAME CARS! 2. Sedagons are NOT allowed. 3. All glass, side windows, rear windows, headlights and taillights, must be removed before reaching the track. Rolling down windows is not permitted. 4. Rear seat of sedan must be removed, top and bottom. On station wagons all seats and decking must be removed. Station wagons must be emptied to the floorboards. 5. Cars must have a seatbelt and working brakes. MANDATORY 6. Battery may be moved, but must be securely fastened and covered in passenger compartment. TWO BATTERIES ARE ALLOWED. 7. Front Windshield Bar is MANDATORY and is limited to a 2” wide x 1/4" thick strap or a chain/9 wire loop
GAS TANKS AND FUEL PUMPS
1. Stock gas tank MUST be removed from original position and mounted in the rear seat area and secured. No rubber or chain straps. All tanks must have a secure cap. A marine tank or fuel cell is strongly recommended. All lines and fitting must be leak proof and meet approval of the track officials. Electric fuel pumps are allowed 2. All lines must be run inside car, not along the frame underneath. 3. All lines should be double clamped.
RADIATOR AND CORE SUPPORT
1. Radiator must be in stock position 2. Any automotive type radiator can be used. Aluminum Radiators are LEGAL. 3. No homemade radiators allowed 4. No reserve tanks and no added cooling capacity. 5. One electric fan, mounted to the radiator, may be used. 6. Factory condenser or 24" wide by 1/4" thick radiator protector
BODY
1. No body seams may be welded. No metal may be added. 2. No doubling of body panels allowed, no added metal allowed. 3. NO Body creasing, 4. Fenders may be bolted together. Max of 10 3/8” BOLTS ABOVE THE FENDER WELL. 5. Doors may be chained, wired, or welded. Welding of the doors is the only welding allowed on the car body. When welding doors 6in 0n 6in off all the way around 6. NO Changing body mounts don"t touch them, except the rear most 4 and the front 2 at the core support
SUSPENSION
1. Suspension must be original factory suspension for that car. SPRING SPACERS ARE ALLOWED 2. Tie rods must have factory appearing ends, No heims! You may brace the center tube with angle or pipe. Aftermarket is fine but must have a factory type end! 3. No solid suspension must bounce
HOODS
MUST BE OPEN AT INSPECTION! 1. Hoods must have two (2) holes, at least four (4) inches in diameter on each side of the carburetor. Not directly on top of the carburetor. If the hood is removed, either the fan or fan belt must be removed. 2. Hoods, trunks, and tailgates must be open during inspection. 3. Hoods may be secured by 2 pieces of all thread outboard the radiator. Cannot be sleeved. 5. Hoods can be held shut with “one” of the following but not both, A (8) 2” long pieces of 2” x 2” angle with a single 3/8” bolt thru them B (8) pieces of # 9 wire attaching hood to fender.
TRUNKS
1. You are allowed Unlimited #9 wire across the front in front of radiator. 2. You may use 4 pieces of all thread to secure the trunk lid. All thread must go thru factory rear body mounts only. Washers may be no larger than 4 inches in diameter. No sleeving the all thread and no nuts directly under the trunk lid. 3. 5. Trunk can be held shut with “one” of the following but not both, A (8 spots) 2” long pieces of 2” x 2” angle with a single 3/8” bolt thru them B (8) pieces of # 9 wire attaching trunk to quarter.
4. The trunk lid must remain on hinges. 5. The trunk lid may be v’d in the center, BUT QUARTER PANELS MUST REMAIN STAINDING. (THIS IS TO GAIN VISION NOT BUILDING A TRUNK)
SAFTEY CAGES
1. All cars must have a safety cage and roll over bar. 2. A 4 point cage is required and limited to 4 points only. Your cage will must have a dash bar that must be 4” from the firewall. Your cage must have a bar behind the driver’s seat no more than 6” away from it. You must have (2) side bars and they must not be farther than the rear wheel humps and must not extend past your dash bar. The side bars must not be welded to the rear humps. 3. Roll over bar cannot be more than 6” behind driver’s seat. Roll over bar cannot attach to frame. Weld or Bolt it to sheet metal only. A 6” x 6” plate may be used in aiding it to be attached to floor sheet metal. Roll over bar can be bolted to roof 4. The cage can be welded to sheet metal only. You can have up to four (4) down posts, two (2) per side. You must have a dash bar, a cross bar behind the seat and two (2) door cross bars. Nothing can be ran between the rear wheel humps or welded to the humps. No kickers to the frame humps- front or back. 5. Cage can be made out of 4” pipe or 4” square tubing, MAX. 6. All down tubes must be at or behind the dash bar, straight up and down. Welded to sheet metal only. 7. Gas tank protectors are NOT allowed, floating your gas tank off the floor is NOT considered a gas tank protector.
FRAMES
1. No welding, plating, or reinforcing of the frame. 2. All factory frame holes must be left open. 3. Any reinforcing of frame found will result in disqualification. 4. Sub frame cars cannot be tied together. 5. You can shorten the front frame only to aid in mounting front bumper. CANNOT BE MORE THAN 3 INCHES AND MUST NOT TOUCH FRONT MOUNT. 6. aftermarket steering columns are ok 7. Rear frame rails may not be shortened. 8. You may chain or wire your axle to the frame hump. (2 CHAIN LINKS WELDED TO FRAME MAX)
BUMPERS
1. Bumpers maybe loaded. Everything inside factory envelope of the bumper. 2. Bumpers may be hardnosed or weld a factory shock to frame and bumper, If you slid the brackets back on the frame No welding on frame beyond the furthest factory attachment point on the frame. (not the furthest point on the bracket/shock) If you have questions about this please call! 3. YOU MAY BOLT A CHAIN FROM BUMPER TO BUMPER SHOCK on THE FRAME 3/8 MAX or weld a piece of strap (2"x 1/4") from frame to bumper 1" overlap on each end. This is to aid in keeping bumpers off the track 4. Bumpers can be no higher than 26" from the ground to the top of the bumper or lower than 16" from the ground to the bottom of the bumper.
ENGINE AND TRANSMISSION 1. Any V6 or smaller engine and transmission may be used in any car, but must be mounted within 6” of the original motor. Engine cannot protrude into the passenger compartment before the race. 2. ENGINE CRADLES ALLOWED(front plate and lower cradle) MUST USE FACTORY RUBBER MOUNTED CLAMS (NO AFTERMARKET MOTOR MOUNTS) 3. No midplates allowed 4. Any items used to adapt an engine to a different make must be approved. I.E. robbo cradle for Chrysler etc. 5. Transmission oil coolers and engine oil coolers are permitted. They must be secure and contained and covered inside the car, for the driver’s protection. 6. Pulley protectors are allowed, but sway bar must be removed or not able to touch before or after race!! 7. No Skid plates. 8. No Distributor protectors. 9.HOMEMADE Gas Pedals and Shifters Are Allowed 10. OEM crossmember or 2x2 square tube. Factory style rubber mount 12. No Driveline pressure
REAR END 1. Any automotive or aftermarket rear end 2. On models originally equipped with leaf springs, stock leaf springs and hangers MUST be used. 3. Leaf packs on all cars MUST be OEM stock. 4. Slider drive shaft is permitted. 5. You may have five (5) spring clamps per spring 6. If you shorten the trailing arms. Minimum overlap and weld. No doubling or reinforced trailing arms.
TIRES 1. Any Tires 15 inches or smaller. 2. No solid wheels stock OEM only. YOU MAY WELD IN WHEEL CENTERS for multi lug use (not full plates to add strength!).
The only welding allowed will be the bumper, the cage, doors, motor mounts, angle on the hood and trunk.
These are all outlined above. If it doesn’t say you can do it, don’t assume that you can.
ASK first or don’t do it!
Everybody needs to read and re-read these rules.
If you are found to be too built for these rules, you will be given 2 options. A. CUT OR REMOVE ILLEGAL PARTS. B. LOAD ON TRAILER AND GO HOME. Either way you will NOT RECEIVE A REFUND.
|
|
wickedridesinc
Feature Winner
https://wickedderby.webconnex.com/UDregistration
Posts: 1,281
|
Post by wickedridesinc on Jan 5, 2016 1:07:24 GMT -5
Windshield class
1. Must be 100% stock!!1980 AND NEWER CARS CALL ABOUT 77-79 No cross breeding entire drive must be same make as car ( Chevy to Chevy ford to ford and so on) Must appear to be factory engine to car with stock exhaust.
2. Engine must be mounted with stock mounts in stock position. No welding of mounts bolted only. No homemade cross members, cross members must be stock and bolted in not welded
3. Doors must be chained or wired. No more than 6 places.
4. Trunks must be chained or wired. No more than 4 places. TRUNKS MUST BEOPEN DURING INSPECTION No welding or adding metal. .You can notch the rear frame. No tucking, wedging, pre bending, smashing, folding or anything else you can think of. No welding washers for holes. You do not have to have a deck lid.
5. NO ALTERING THE SHEETMETAL ON ANY PART OF THE CAR OTHER THAN WHAT IS ALLOWED
6. Hoods may be wired or chained in 4 spots. X chain or 2 strands per hole. It must be sheet metal to sheet metal only. No welding washers for holes. Must be 12" hole in hood in case of fire. Remove hood latch!!! Hood must be open for inspection.
7 .Any tires permitted no valve stem protectors or rim guards.
8. You may leave stock gas tank in stock location if its in front of the rearend if it is behind rearend it must be moved inside the car you may relocate the fuel tank to rear floor of car if this is done you must use a fuel cell or boat tank no stock fuel tanks permitted inside of car.
9. Windshield may be left in car you can remove windshield!
10. The following must be removed prior to entering the fairgrounds, windows, headlights, taillights, all chrome and mirrors, all fiberglass must be removed. Interior must be swept clean of debris and glass.
11. Stock type springs and shocks. spring risers allowed in the FRONT ONLY, No solid suspension, wire, chains or any welds on spring pockets
12. WELDING REAR ENDS PERMITTED
13 Paint front doors in contrasting paint. Example if the car is black paint doors white
14. Do not strip under the hood. . But you may move the battery to the passenger side floor YOU MAY ONLY MOVE THE BATTERY CABLES TO THE FLOOR NOT THE WIREING HARNIS THIS WILL BE STRICKLY ENFORSED. You may move wiring harness inside the front body bolts but the harness MUST remain infront of the radiator and core support in factory condition.
15. YOU MAY USE Any 80 & NEWER BUMPER ON CAR THEY MUST BOLT ON IN FACTORY LOCATION AND MANNER YOU MAY WELD THE BUMPERS WITH 2 ONE INCH WELDS ON TWO SIDES OF THE BUMPER BRACKETS YOU MAY ALSO WELD THE BUMPER SHOCK TO THE FRAME ONLY AROUND THE OPENING OF THE FRONT OF THE FRAME NO SINKING THE BUMPER SHOCKS THEY MUST STAY IN THE FACTORY LOCATION
16. Read all rules carefully and follow them! It will be a cheap easy build. Any questions call! There will be no stretching or bending of any rules or you will either load it run in the modified class.
17. YOU MAY NOTCH/DIMPLE THR REAR FRAME
18. You may have a wire or strap to help hold up the seat NO WELDING OF ANY KIND.
19. IF YOU HAVE A PRE RAN CAR CALL FIRST.
|
|
wickedridesinc
Feature Winner
https://wickedderby.webconnex.com/UDregistration
Posts: 1,281
|
Post by wickedridesinc on Jan 5, 2016 1:07:37 GMT -5
Mini Truck Rules
1. Any American made pick up, suburban and blazer type vehicles permitted. 2. Factory fuel tanks must be removed. 3. You may run engine of choice. No distributor protector 4. Fuel tanks must be located in the bed of the trucks in the in the center of the bed directly behind cab. No stock fuel tanks permitted. Fuel cells must be securely fastened and covered. 5. Battery may be moved to front floor of cab. Battery must be securely fastened to floor and covered. 6. All trucks must have seat belts. 7. Doors must be secured by wire, chain, or welded. If welded must use a 5 on 5 off pattern 8. Tail gates may be bolted shut in 8 spots or wired or chained. 9. Box and cab mounts may be replaced with up to 1” bolts body mounts may be removed. The body bolts may go all the way through the fame and floor of truck. 10. No trailer hitches or reinforcements of frame or body of any kind permitted. May use car bumpers for mounting of car bumpers you may use factory bumper shocks and brackets no welding past the 6" mark on the frame. 11. Hoods must be in place and operable must have a 12” X 12” hole cut in hood over carburetor 12. Hoods may be wired or bolted shut in 8 places 1" max bolt size and have unlimited wire from hood to bumper 13. No 4 wheel drives permitted 4 wheel drives must have front drive shaft removed. 14. Tires MUST be D.O.T. TIRE sizes for trucks no split rims. NO TRACTOR TREADS, IMPLIMENT TIRES OR OTHER OFF ROAD TIRES WIL BE PERMITTED 15. Beds must be welded to cab of trucks with a 3” strap I'ma 5 on 5 off ppattern directly behind doors. 16. Unlimited double strands of wire permitted from tailgate to bumper 17. Suspension must BOUNCE factory suspension, may run spring risers 18. A 4 point cage is highly recommended in drivers compartment for drivers safety. The cage in the cab may have 4 down legs from front and rear bar straight down to the body only. Also a gas tank protector is highly recommended. Protector may attach to frame but may not extend further than 24” from the front of the bed. 19. Trucks must set level no pulling down rear of the truck. No smashing of the bed sides will be permitted. You must use factory springs for make and model of truck. NO all threadshocks
|
|
wickedridesinc
Feature Winner
https://wickedderby.webconnex.com/UDregistration
Posts: 1,281
|
Post by wickedridesinc on Jan 5, 2016 1:07:51 GMT -5
STOCK MOWER RULES
*. DRIVER MUST HAVE LONG-SLEEVE SHIRT, AND PANTS HELMET MUST BE WORN AT ALL TIMES MUST HAVE SOME SORT OF EYE PROTECTION ON.
1) no welding on frame other then stated in rules... 2) no front bumpers. 3) fenders can be slammed down no wider then tires. 4) a 2x2 any thickness cage is permitted around YOU. Cage has to be NO wider then the back wheels. U can have only one bar per side off the cage welded to the side or top of frame behind motor only. Cage only can come to the end of the foot rest. straight down legs only to foot rest. Make it good so no one gets hurt... 5) you can sheet sides of leg bars only for safety. No sheeting any other places. 6) frame creasing is aloud. U can tilt front but no welding aloud. 7) any lawn mower tire is allowed. 8) you can use hood of choice no home made shit factory mower hoods only.. 9) back bumper is permitted between the rear tires can not stick out further than rear tires. 10) pulley's can be any size u prefer. 11) no battery's.
|
|
wickedridesinc
Feature Winner
https://wickedderby.webconnex.com/UDregistration
Posts: 1,281
|
Post by wickedridesinc on Jan 5, 2016 1:08:05 GMT -5
MODIFIED MOWER RULES 1. MOWER MUST BE A FACTORY AVAILABLE MOWER LAWN OR GARDEN MOWER (NO HOME MADE FRAMES) 2. NO REAR ENGINE LAWN MOWERS ARE ALLOWED. 3. ENGINE MUST BE FACTORY LAWN MOWER ENGINE SUCH AS BRIGGS & STRATTON, TECUMSEH, ONAN ETC. 4. ALL FRAME MODIFICATION AND FRAME REINFORCING WILL BE ALLOWED. 5. TRANSAXLES MUST BE FACTORY AVAILABLE MOWER TRANSAXLES BUT ANY REINFORCING AND/OR WELDING OF SPIDER GEARS IS PERMITTED 6. ENGINE BAY REINFORCING IS PERMITTED BUT MUST BE CONTAINED INSIDE OF HOOD AND MUST MAINTAIN FACTORY BODY LINES 7. ALL MOWERS MUST RUN A FACTORY HOOD AND FENDERS AND HAVE THE HOOD EITHER SCREWED OR WELDED DOWN TO DASH PANEL AROUND DRIVERS AREA ( NOTE IF HOOD IS FIBERGLASS YOU CAN MAKE ONE OUT OF SHEET METAL ONLY BUT MUST BE THE SAME SIZE AS THE FIBERGLASS ONE) 8. MOWERS MUST HAVE GOOD BRAKES AND FORWARD AND REVERSE GEARS AT THE START OF THE HEAT. 9. GAS TANK MUST BE SECURED AND HAVE A CAP ON IT (ANY GAS AT ALL LEAKING AND YOU WILL BE ASK TO SHUT IT DOWN) 10. LEG GUARDS ARE MANDATORY AND MUST BE BOLTED AND/OR WELDED FROM REAR FENDER TO FRONT OF FOOT REST OR FRAME (CALL ?) 11. A REAR BUMPER IS PERMITTED BUT IS NOT ALLOWED TO EXTEND MORE THEN 4 INCHES OUT AND IT MUST STAY IN BETWEEN THE TIRES ALSO NO SPIKES,SHARP EDGES OR ANY PROTRUSIONS ALLOWED (BUMPER CAN BE HOME MADE WITH I/H BEAM OR SQ. TUBING. CALL?) 12. REGEARING AND CHANGING OF PULLEYS TO INCREASE SPEED IS PERMITTED AND ENCOURAGED. 13. ANY AND ALL DRIVE TRAIN MODIFICATIONS IS PERMITTED BUT MUST STAY BUILT DRIVEN. 14. ALL MOWERS MUST USE LAWN MOWER TYPE WHEELS TRACTOR TREADS AND CUT TIRES WILL BE PERMITTED BUT NO TIRE CHAINS OR DUAL WHEELS WILL BE ALLOWED. 15. MOWER DECKS MUST BE REMOVED 16. ALL HEAD LIGHTS AND ANY OTHER GLASS AND PLASTICS MUST BE REMOVED BEFORE YOU ENTER THE PITS. 17. BATTERIES MUST BE REMOVED FROM MOWER AND ONLY USED TO JUMP START THE MOWER BEFORE THE HEAT BEGINS IF A PULL START IS USED DRIVER WILL NOT BE PERMITTED TO RESTART ENGINE DURING THE HEAT. 18. NO FRONT BUMPERS YOU CAN BUILD UP THE FRONT OF THE FRAME AND UNDERNEATH THE GRILL TO HIT WITH. THE FRONT OF THE MOWER MUST BE A SMOOTH FINISH FOR SAFTEY. 19. ROLE-OVER* DRIVER IS OUT OF HEAT ALSO IF A DRIVER TOUCHES THE GROUND WITH A HAND OR A FOOT DRIVERS IS ALSO OUT OF THE HEAT 20. FOR SAFTEY IF A MOWER DOES ROLE OVER ALL DRIVERS MUST STOP AND WAIT UNTIL THAT DRIVER UP-RIGHTS HIS MOWER AND GETS OFF THE TRACK 21. PLEASE PUT YOUR NUMBER ON EACH SIDE OF YOUR MOWER OR YOUR HELMET SO WE CAN TRACK THE WINNERS. 22. all mowers must be belt driven only.
|
|
crazychris03
Heat Winner
Enter your message here...
Posts: 398
|
Post by crazychris03 on Jan 9, 2016 14:23:42 GMT -5
What are the rules for this show what kind of car can you run
|
|
wickedridesinc
Feature Winner
https://wickedderby.webconnex.com/UDregistration
Posts: 1,281
|
Post by wickedridesinc on Jan 25, 2016 12:47:58 GMT -5
updated, and more info to come
|
|
crazychris03
Heat Winner
Enter your message here...
Posts: 398
|
Post by crazychris03 on Jan 26, 2016 12:15:52 GMT -5
updated, and more info to come Are there any modified cars in this show like seam weilded body's
|
|
wickedridesinc
Feature Winner
https://wickedderby.webconnex.com/UDregistration
Posts: 1,281
|
Post by wickedridesinc on Jan 26, 2016 15:30:49 GMT -5
no pro mod cars etc
hard cars will be kicker rules which will be the 2016 smash it rules. I'll post soon,
|
|
crazychris03
Heat Winner
Enter your message here...
Posts: 398
|
Post by crazychris03 on Jan 26, 2016 17:59:30 GMT -5
no pro mod cars etc hard cars will be kicker rules which will be the 2016 smash it rules. I'll post soon, so there no seam wielding at any of our shows just smash it modified they run seam weilded cars so we can run them at this show
|
|
wickedridesinc
Feature Winner
https://wickedderby.webconnex.com/UDregistration
Posts: 1,281
|
Post by wickedridesinc on Feb 1, 2016 1:51:30 GMT -5
correct
|
|
crazychris03
Heat Winner
Enter your message here...
Posts: 398
|
Post by crazychris03 on Feb 2, 2016 14:31:38 GMT -5
so witch one is it we can or no we cant
|
|
wickedridesinc
Feature Winner
https://wickedderby.webconnex.com/UDregistration
Posts: 1,281
|
Post by wickedridesinc on Feb 2, 2016 16:28:31 GMT -5
so witch one is it we can or no we cant What are you calling seam welded ? body, frame?
|
|
|
Post by mtnman26 on Feb 2, 2016 20:45:41 GMT -5
so who exactly do we make the money order out to? the Lawrence county agricultural society?
|
|