METRIC CLASS
METRIC / Limited Weld (these are the rules still have some clarification to finalize)
ALL JUDGES DECISIONS ARE FINAL
Only 50% of your car can be painted black! NO ALL BLACK CARS!!!!
BRAND SPECIFIC RULES
GM
YOU ARE ALLOWED A 6" X 22"-1/4" THICK ARCH PLATE. MUST BE CENTERED ON THE HUMP AND ON THE WHEEL SIDE OF THE HUMP. DOES NOT HAVE TO BE CONTOURED TO FRAME CAN RUN STRAIGHT ACROSS.
FORD/LINCOLN/MERCURY
YOU ARE ALLOWED TO TILT YOUR CARS AT THE CRUSH BOX BY CUTTING THE SIDE FLAP, 8" MAX SPACER AT CORE SUPPORT
MOPAR
YOU ARE ALLOWED A 7 LEAF SPRING PACK, 5 CLAMPS, 2" STAGGER ON SPRINGS. YOU MAY ALSO CHANGE YOUR 4 FRONT SUB/K FRAME BOLTS
1. ANY METRIC Passenger car or station wagon only.(MOST 1977 & UP GM, 1979 & NEWER FORD, MERCURY,CHRYSLER AND 1980 AND NEWER LINCOLNS) IF YOU HAVE MODEL THAT IS IN QUESTION CALL, DO NOT ASSUME! No trucks, jeeps, hearses, limousines.
2. Sedagons are NOT allowed.
3. All glass, side windows, rear windows, headlights and taillights, must be removed before reaching the track. Rolling down windows is not permitted.
4. Rear seat of sedan must be removed, top and bottom. On station wagons all seats and decking must be removed. Station wagons must be emptied to the floorboards.
5. Cars must have a seatbelt and working brakes. MANDATORY
6. Battery may be moved, but must be securely fastened and covered in passenger compartment. TWO BATTERIES ARE ALLOWED.
7. Front Windshield Bar is MANDATORY and is limited to a 2” wide x 1/4" thick strap or a chain/9 wire loop
GAS TANKS AND FUEL PUMPS
1. Stock gas tank MUST be removed from original position and mounted in the rear seat area and secured. No rubber or chain straps. All tanks must have a secure cap. A marine tank or fuel cell is strongly recommended. All lines and fitting must be leak proof and meet approval of the track officials. Electric fuel pumps are allowed
2. All lines must be run inside car, not along the frame underneath.
3. All lines should be double clamped.
RADIATOR AND CORE SUPPORT
1. Radiator must be in stock position
2. Any automotive type radiator can be used. Aluminum Radiators are LEGAL.
3. No homemade radiators allowed
4. No reserve tanks and no added cooling capacity.
5. One electric fan, mounted to the radiator, may be used.
6. DO NOT MOVE CORE SUPORT
7. Factory condenser or 24" wide by 1/4" thick mesh radiator protector
BODY
1. No body seams may be welded. No metal may be added.
2. No doubling of body panels allowed, no added metal allowed.
3. BODY CREASING IS LIMITED TO REAR QUARTER PANELS AND TRUNK ONLY
4. Fenders may be bolted together. Max of 10 3/8” BOLTS ABOVE THE FENDER WELL.
5. Doors may be chained, wired, or welded. Welding of the doors is the only welding allowed on the car body. When welding doors 6in 0n 6in off all the way around
6. NO Changing body mounts don"t touch them, except the rear most 4 and the front 2 at the core support (1" threaded rod max) 2 OF YOUR REAR ALL THREAD CAN GO THREW A FACTORY HOLE AND 2 CAN BE WELDED TO SIDE OF THE FRAME WITH A SINGLE BEAD OF WELD.
SUSPENSION
1. Suspension must be original factory suspension for that car. SPRING SPACERS ARE ALLOWED
2. Tie rods must have factory appearing ends, No heims! You may brace the center tube with angle or pipe. Aftermarket is fine but must have a factory type end!
3. No solid suspension must bounce
4. factory spindle swaps are ok, ford to chevy etc.
HOODS
MUST BE OPEN AT INSPECTION!
1. Hoods must have two (2) holes, at least four (4) inches in diameter on each side of the carburetor. Not directly on top of the carburetor. If the hood is removed, either the fan or fan belt must be removed.
2. Hoods, trunks, and tailgates must be open during inspection.
3. Hoods may be secured by 2 pieces of all thread outboard the radiator. Cannot be sleeved.
4. You are allowed 10 pieces of double stranded #9 wire across the front of car from bumper to hood/coresupport
5. You may replace your front core support bolts with upto 1" allthread, and it can extend threw the hood. This may not be sleeved with pipe or tube.
6. Hoods can be held shut with “one” of the following but not both,
A (8) LOCATIONS 2” long pieces of 2” x 2” angle with a single 3/8” bolt thru them
B (8) pieces of # 9 wire attaching hood to fender.
TRUNKS
1. You are allowed 10 pieces of double stranded #9 wire from bumper to bottom of trunk lip.
2. You may use 4 pieces of all thread to secure the trunk lid. 2 OF THE ALL THREAD MUST GO THROUGH FACTORY BODY MOUNT HOLES AND 2 CAN BE WELDED TO THE SIDE OF THE FRAME WITH A SINGLE BEAD OF WELD. Washers may be no larger than 4 inches in diameter. No sleeving the all thread and no nuts directly under the trunk lid.
3. You may have 8 spots on your trunk to hold it down, use the following methods, 2" long angle back to back with a 3/8 bolt, 8 spots of additional wire, 8 3/8" bolts threw rain rail.
4. The trunk lid must remain on hinges. (i.e no sliding it forward)
SAFTEY CAGES
1. All cars must have a safety cage and roll over bar.
2. A 4 point cage is required and limited to 4 points only. Your cage will must have a dash bar that must be 4” from the firewall. Your cage must have a bar behind the driver’s seat no more than 6” away from it. You must have (2) side bars and they must not be farther than the rear wheel humps and must not extend past your dash bar. The side bars must not be welded to the rear humps.
3. Roll over bar cannot be more than 6” behind driver’s seat. Roll over bar cannot attach to frame. Weld or Bolt it to sheet metal only. A 6” x 6” plate may be used in aiding it to be attached to floor sheet metal. Roll over bar can be bolted to roof
4. The cage can be welded to sheet metal only. You can have up to four (4) down posts, two (2) per side. You must have a dash bar, a cross bar behind the seat and two (2) door cross bars. Nothing can be ran between the rear wheel humps or welded to the humps. No kickers to the frame humps- front or back.
5. Cage can be made out of 4” pipe or 4” square tubing, MAX.
6. All down tubes must be at or behind the dash bar, straight up and down. Welded to sheet metal only.
7. Gas tank protectors are NOT allowed, floating your gas tank off the floor is NOT considered a gas tank protector. MUST BE A 4" GAP BETWEEN GAS TANK MOUNT AND PACKAGE TREY
FRAMES
1. No welding, plating, or reinforcing of the frame.
2. All factory frame holes must be left open.
3. Any reinforcing of frame found will result in disqualification.
4. Sub frame cars cannot be tied together. If you want to run a full frame car, buy a full frame car, don’t build one.
5. CORE SUPPORT AND CORE SUPPORT MOUNT MUST REMAIN IN FACTORY LOCATION.
6. aftermarket steering columns are ok
7. Rear frame rails may not be shortened.
8. You may chain or wire your axle to the frame hump. (2 CHAIN LINKS WELDED TO FRAME MAX) *NO OPENING CHAIN LINKS TO GAIN LENGTH*
BUMPERS
1. Bumpers maybe loaded. Everything inside factory envelope of the bumper.
2. Bumpers may be hardnosed or weld a factory shock to frame and bumper, If you slid the brackets back on the frame No welding on frame beyond the furthest factory attachment point on the frame. (not the furthest point on the bracket/shock) If you have questions about this please call!
3. YOU MAY BOLT A CHAIN FROM BUMPER TO BUMPER SHOCK on THE FRAME 3/8 MAX or weld a piece of strap (2"x 1/4") from frame to bumper 1" overlap on each end.
This is to aid in keeping bumpers off the track
4. Bumpers can be no higher than 26" from the ground to the top of the bumper or lower than 16" from the ground to the bottom of the bumper.
ENGINE AND TRANSMISSION
1. Any engine or transmission may be used in any car, but must be mounted within 6” of the original motor. Engine cannot protrude into the passenger compartment before the race.
2. ENGINE CRADLES ALLOWED(front plate and lower cradle) MUST USE FACTORY RUBBER MOUNTED CLAMS (NO AFTERMARKET MOTOR MOUNTS)*ANYTHING OTHER THAN AN OEM CHEVY RUBBER CLAM MUST BE APPROVED BY ME*
3. No midplates allowed
4. Any items used to adapt an engine to a different make must be approved. I.E. robbo cradle for Chrysler etc.
5. Transmission oil coolers and engine oil coolers are permitted. They must be secure and contained and covered inside the car, for the driver’s protection.
6. Pulley protectors are allowed, but sway bar must be removed or not able to touch before or after race!!
7. No Skid plates.
8. No Distributor protectors.
9. Factory aluminum engine cradles in 2003 and newer cars may NOT be changed. No homemade cradles.
10.HOMEMADE Gas Pedals and Shifters Are Allowed
11. OEM crossmember or 2x2 square tube. Factory style rubber mount
12. No Driveline pressure
REAR END
1. Any automotive or aftermarket rear end
2. On models originally equipped with leaf springs, stock leaf springs and hangers MUST be used.
3. Leaf packs on all cars MUST be OEM stock.
4. Slider drive shaft is permitted.
6. You may have five (5) spring clamps per spring. Maximum 1" wide 1/4 thick
7. ZTR style brackets are legal, but must use factory trailing arms to mount rear end.
8. If you shorten the trailing arms. Minimum overlap and weld. No doubling or reinforced trailing arms.
TIRES
1. Any Tires 15 inches or smaller.
2. No solid wheels stock OEM only. YOU MAY WELD IN WHEEL CENTERS for multi lug use (not full plates to add strength!).
The only welding allowed will be the bumper, the cage, doors, motor mounts, angle on the hood and trunk.
These are all outlined above. If it doesn’t say you can do it, don’t assume that you can.
ASK first or don’t do it!
Everybody needs to read and re-read these rules.
If you are found to be too built for these rules, you will be given 2 options.
A. CUT OR REMOVE ILLEGAL PARTS.
B. LOAD ON TRAILER AND GO HOME.
Either way you will NOT RECEIVE A REFUND
Read more:
we-crash.proboards.com/thread/61091/000-wicked-team-derby-october#ixzz4C5W1ovZU