|
Post by tomsbrookfire on Feb 12, 2016 13:31:23 GMT -5
1. Power wheels- Ages 3 - 9yrs.. $10.00 entry Fee.. Stock battery can be replaced with 12 volt lawn mower battery ONLY. Only one battery and no changing battery during the heat. It can be positioned any where in car covered and secured not in passenger seat. Secure hoods and doors so they don't come open. Seat belts are not mandatory but recommended. Helmets are mandatory. Rollover bars are aloud if anything is deemed not safe it will be taken off.there will be a 15 min limit on this event. Only one parent is aloud on track with child during the heat
|
|
|
Post by tomsbrookfire on Feb 12, 2016 13:35:02 GMT -5
2.Lawn Mowers - age 16yrs $40.00 entry fee... 100% payback Any factory Belt driven lawnmower except rear engine mowers like the snapper.. Decks must be removed, Exhaust stacks are allowed must go up not going out. Must weld bars to side of mower for leg protection. If battery or gas tank is in front of motor must be moved to safer place. you may rig up hand throttle to run wide open. You may bolt or wire hood down tight. You may weld or bolt spark plug protector, you may weld bumpers on front and back No taller than 15 inches no wider than the tires. Nothing can protect tires in anyway. No frame reinforcements except for mounting bumpers and leg protectors. No hitting in leg area front to front hits are the best. Rear hits use caution. You may change pulleys to get different speeds. NO home made mowers. Helmets and safety glasses are a must.
|
|
|
Post by tomsbrookfire on Feb 12, 2016 13:37:54 GMT -5
Compacts - age 16yrs $50.00 Entry Fee 100% payback. 1.If 20 or more compacts there will be heats and feature. 2. Any 4 or 6 cylinder front wheel drive. 3. This is a basic stock class with a few exceptions 4. Bar chain or wire in windshield for safety 5. All glass plastic and wheel weights must be removed prior to derby. 6. Doors - you may weld doors in three spots on each seam 3 inches long with 2 inch straps 7. Bumpers - you may use any auto bumper. homemade bumpers are permitted no longer than 3 inches in diameter nothing else welded to it. you may run support back into uni body for bumper support no further back than 1 ft. This will be checked. 8. Suspension - must remain stock 9. Tires- any size tire no screws or valve stem protectors. no studded tires are allowed. 10. Gas Tanks - may be moved to the rear seat area must be covered and all lines must be double clamped you may leave tank under the car in front of rear axle. must have a metal skid plate skid plate must be durable sheet metal. 11. Cage - 4 point cage recommended door bar not to exceed past rear of front door 6inches. 12. Body- No wedging you may pre bend rear of car to go up. 13. Battery - Any size battery must be in front passenger floor board. covered and secured. Helmets and safety glasses are a must. 14. Roof signs must be 2ft by 2ft with number. 15. You must wire and chain 6 spots on hood and trunk. Gas tank protectors must be 6 inches off any sheet metal. Only be attached to the seat bar. No wider than gas tank. NO PLASTIC GAS TANKS
|
|
|
Post by tomsbrookfire on Feb 12, 2016 13:45:49 GMT -5
full size - age 16 yrs - $50.00 entry fee Any full size car except for limo's so guys if you have any imperial's or hearse's build and bring them.
1. All glass must be removed from car. All plastic must be removed. Must remove all wheel weights. 2. Gas tanks All gas tanks must be removed from under the car. No plastic gas tanks, double clamp fuel tanks. gas tank must be in back seat area. covered and secured. 3. Suspensions - you may leaf spring your car no more than 5 leafs and no wider than 3 inches. No more than 4 clamps per side. front suspension may be locked, front bumper height no more than 24 inches from bottom of bumper. rear bumper height no lower than 18 inches from bottom of bumper. After market suspension parts are permitted no excessive bracing. you may leaf spring the front of the car must use a straight axle no more than 5 leafs per side, no more than 4 clamps per side. 4. Doors - All doors may be welded with a strap no wider than 3 inches. tops of doors may be beat down and welded. you may wire or chain doors as well. 5. Trunk - Trunk may be pre bent or tucked but not fully wedged. must have at least 8 inches of clearance between trunk lid and all of floor. speaker tray must remain in stock position on the sides. you can run a bar from the roof to no further than half the truck lid.may weld trunk with straps no wider than 3 inches. 6. Cage - you may run door bars from dash bar all the way back to the rear fender wells. gas tank protector can be a 2 inch bar ran from end of door bar to end of door bar. And a 2inch bar ran on both sides of gas tanks. roll over bars are permitted. Kickers we are allowing 2 no bigger than 2 inches in diameter if any kicker is bigger than that they will be cut completely out.kickers must go from dash bar to front frame rail just behind the a arms. If you have down bars off of your cage they must be at a 90 degree angle and must be welded to sheet metal only. Exception of a bar coming from door bar to the frame on drivers door. 7. Hood and core support - Core support may be bolted with all thread no larger than 3/4. you can run it all the way thru the hood to bold hood down. you may chain, wire or bolt hood down. A 2ft by 2ft. hole must be in hood for fire detection. Can bolt hood down 6 spots. 8. Battery - one battery of any size is permitted in front passenger floor board. secured and covered. 9. Tires - No studded tires no screws are allowed valve stem protectors are permitted. Solid rims are allowed. Any tire size is permitted. foam filled double tires are permitted. 10. Radiator - You must have radiator in stock position you may use water barrel it is only to be welded in two spots on frame. Not to be attached to bumper. 11. Bumpers - Any bumper may be used, you may use homemade bumper it must be no bigger than 4 inches in diameter. nothing to be welded to it. other than attaching it to the frame. weld it good don't want it to fall off. bumpers must be a straight piece of metal. we know how hard it is to find bumpers. you may hard nose your frame.you may weld a plate no longer than 10 inches per frame rail measuring from the back of the bumper.and no wider than the frame.at a 1/4 thick. Your preference on which side.top bottom or side. This is to be used as a bumper bracket. 12. Rear end - Rear end of any make up to 3/4 ton rear ends. No excessive of rear end bracing. you may weld braces from backing plate to backing plate only. 13. Windshield - must have at least one bar, chain or wire attached for protection from hood. 14. Body Mounts - Body mount bolts no larger than 5/8 .no extra body mounts bolts. washers will be no larger than 2 inches of plate 1/4 thick. 15. Body - No extra metal on body. if it is a pre ran car you can patch sheet metal of same thickness and not to exceed 2 inches past tear in sheet metal. you may bolt fender and quarter panels. 16. Frame - Hump plates are permitted they can be no bigger than 4 inches by 2ft. 1/4 inch thick. you may seam weld top and bottom front to back. no filling in of factory holes. if pre ran car and have bent frame you may plate where it is bent with 1/4 inch plate. not to exceed past bend or tear 1 inch. frames must be empty will be checked. 17. Distributor protectors are permitted. 18. Transmission coolers must be kept in back seat area with lines double clamped. If it has a fan it must be secured. if using separate battery for fan 12 volt lawn mower battery only covered and secured. 19. Roof sign must be 2ft by 2ft with number on it.
Re
|
|
|
Post by tomsbrookfire on Feb 12, 2016 15:11:03 GMT -5
mini vans suv's and compact trucks 16years of age and up
50.00 to entry 100% payback
1. Strip all glass plastic and interior and all wheel weights. 2. must be 2wd if 4wd must take one of the driveshaft's your choice on which one 3. must be a 4 or 6cl engine 4. compacts trucks can only be 2 dr or extended cab no 4 doors 5. suv's no suburban's, Tahoe's or full size broncos must be considered a small suv 6. suspension may be locked with one piece of steel attached to lower a arm to the frame or unibody on each side no leaf spring conversions 7.may weld the doors with 2inch straps no more than 6 spots per door you may also chain or wire door. tailgates on all vehicles may be welded In three spots with 2inch strapping 8. its recommend to have a 4 point cage 9. tires of any size no valve stem protectors 10. a bar or chain must be place in the center of windshield for protection 11.one battery of any size must be place in front floorboard secured and covered 12.compact trucks gas tanks placed in the bed area against cab in center secured and double clamp each line 13. suv gas tanks must be placed in rear seat area secured and covered with double clamp each line 14. bumpers you may weld bumper you may also have a home made bumper no more than 3 inches in diameter nothing welding to it. you may hard nose the bumpers 15. no trailer hitches allowed 16. no plating of frame in any places 17.no wedging of any kind 18. you may change body mount bolts can be no bigger than 1/2 in diameter
19.you may chain or wire your hoods in six places no all thread
|
|
|
Post by tomsbrookfire on Feb 12, 2016 15:18:41 GMT -5
will be paying out 4000.00 for 1st place in full size class and will be paying 1500.00 for compacts. all classes are 100% payback
|
|
|
Post by tomsbrookfire on Feb 12, 2016 15:27:14 GMT -5
also starting Monday 2/15/16 if you would like a set of rules come to jpg towing office at 3569 n main st toms brook
|
|
|
Post by tomsbrookfire on Mar 1, 2016 13:43:24 GMT -5
Shenendoah county fair woodstock va rules are on my desk just waiting on approval then i will post
|
|
|
Post by mousie218 on Mar 10, 2016 21:34:40 GMT -5
So nothing can be done to compact suspension? Has to be completely stock
|
|
grinder
Heat Winner
patina
Posts: 281
|
Post by grinder on Mar 11, 2016 11:09:13 GMT -5
just out of curiosity...where does this you can leaf the front end of a car even come from??
|
|
|
Post by redneckracing12 on Mar 11, 2016 16:47:18 GMT -5
just out of curiosity...where does this you can leaf the front end of a car even come from?? That's a first for me. Iv never seen that rules before.
|
|
212
Future Icon
Posts: 35
|
Post by 212 on Mar 11, 2016 21:47:00 GMT -5
One of the cars that ran last year did this on a 03 n newer so they added that rule in I'm just assuming that's where it's coming from
|
|
|
Post by junkit52 on Apr 10, 2016 14:59:22 GMT -5
In compact class can we convert cars to a carburetor? Also in compact class can we load stock automotive bumpers?
|
|
|
Post by tomsbrookfire on May 6, 2016 15:12:23 GMT -5
No to carbs conversion . No loaded bumpers u can make ur own bumper
|
|
|
Post by tomsbrookfire on May 6, 2016 15:13:12 GMT -5
If anyone has question's call jason 5403357510
|
|