|
|
Post by derbyannouncer on Jul 28, 2015 23:13:23 GMT -5
SATURDAY, SEPTEMBER 5, 2015 7:00 PM THREE QUALIFYING HEATS FOR THE NEW HAMPSHIRE STATE CHAMPIONSHIP TOP THREE CAR PER HEAT RECEIVE $100.00 AND A TROPHY AND TRANSFER TO THE CHAMPIONSHIP ON SUNDAY NIGHT FRONT WHEEL DRIVE DEMOLITION DERBY ~ONE RUN AND DONE~ ANY 4 OR 6 CYLINDER FRONT WHEEL DRIVE VEHICLE WITH A WHEEL BASE OF 111" MAXIMUM $1000.00 FIRST PLACE, A TROPHY AND QUALIFIES FOR CHAMPIONSHIP ON SUNDAY NIGHT (MUST USE A FULL SIZE CAR) $500.00 SECOND PLACE AND A TROPHY $250.00 THIRD PLACE AND A TROPHY SUNDAY, SEPTEMBER 6, 2015 7:00 PM 4 OR 6 CYLINDER FRONT WHEEL DRIVE CARS, ONE RUN AND DONE, $500.00 MINIMUM TO WINNER 100% PAY BACK. WINNER TRANSFERS TO NEW HAMPSHIRE STATE CHAMPIONSHIP, YOU MUST USE A FULL SIZE CAR. THREE QUALIFYING HEATS FOR THE NEW HAMPSHIRE STATE CHAMPIONSHIP TOP THREE CARS PER HEAT RECEIVE $100.00 AND TRANSFER TO THE CHAMPIONSHIP ***YOU CAN USE A FRESH CAR FOR THE FEATURE.*** WINNER $7,500.00 TROPHY AND JACKET SECOND $2,000.00 AND A TROPHY THIRD $1,000.00 AND A TROPHY FOURTH $500.00 AND A TROPHY FIFTH $250.00 AND A TROPHY Info at www.woodboogerdemoderby.net |
|
|
|
Post by derbyannouncer on Jul 28, 2015 23:16:09 GMT -5
SAFETY RULES
1. YOU MUST HAVE A WORKING SEAT BELT, AND IT MUST BE BUCKLED.
2. YOU MUST WEAR LONG PANTS, NO SHORTS.
3. DRIVER DOOR MUST BE PAINTED FLOURESCENT GREEN.
4. DRIVER DOOR AND VERTICAL PIPE BEHIND DRIVER’S SEAT MUST BE PADDED.
5. NO SMOKING ALLOWED ON THE TRACK. YOUR HELMET MUST REMAIN ON AT ALL TIMES.
6. IT IS HIGHLY RECOMMENDED THAT EACH VEHICLE HAVE A FIRE EXTINGUISHER LOCATED IN THE PADDING OF THE FRONT PASSENGER SEAT.
DRIVING RULES
1. YOU MUST MAKE CONTACT EVERY 60 SECONDS. YOU MUST GIVE NOT RECEIVE
2. DO NOT HIT THE DRIVER’S DOOR. IF YOU SEE GREEN DO NOT HIT IT.
3. EXCESSIVE SMOKING WILL BE DISQUALIFIED.
4. SANDBAGGERS WILL BE DISQUALIFIED.
5. RED FLAG MEANS STOP. BLACK FLAG MEANS YOU ARE DISQUALIFIED. PAY ATTENTION.
6. THE LAST CAR TO MAKE A HIT WILL BE DEEMED THE WINNER. OFFICIALS’ DECISION IS FINAL.
CAR PREPARATION
1. YOU MUST HAVE A ROOF SIGN WITH YOUR NUMBER PAINTED ON IT. ANY NUMBER OR WORD (NOTHING OFFENSIVE) IS ALLOWED. NO OFFENSIVE WORDING OR GESTURES ON VEHICLES, THIS IS A FAMILY SHOW.
2. ANY PASSENGER CAR, NO IMPERIALS, PRE 1970 LINCOLNS, HEARSES OR LIMOSINES. PRE-DERBIED CARS ARE ACCEPTABLE AS LONG AS THEY ARE NOT RE-ENFORCED.
3. REMOVE ALL GLASS INCLUDING THE WINDSHIELD. DOORS MUST BE CLEAN AND FREE OF GLASS.
4. REMOVE ALL LIGHTS AND MOLDINGS AND ANYTHING ELSE THAT COULD BE KNOCKED LOOSE ONTO THE TRACK.
5. FUEL TANKS MAY BE MOVED INSIDE OF THE CAR, FORWARD OF THE REAR WHEELS AND BEHIND THE FRONT SEAT. FUEL TANKS MUST BE METAL, SIX (6) GALLON MAXIMUM. FUEL TANK MUST BE SECURE AND DEEMED SAFE BY THE INSPECTORS. YOU MUST COVER THE FUEL TANK. ANY STOCK FUEL TANK ORIGINALLY LOCATED BEHIND THE REAR AXLE MUST BE REMOVED. STOCK TANK LEFT IN ORIGINAL POSITION MUST HAVE NO MORE THAN SIX (6) GALLONS OF GAS.
6. ONE BATTERY ONLY. BATTERY MAY BE MOVED TO PASSENGER SIDE FRONT FLOOR AND MUST BE COVERED WITH A RUBBER MAT. IF BATTERY IS LEFT IN PLACE, SPRAY FOAM CANNOT EXCEED 6 INCHES FROM BATTERY.
7. ANY AIR FILLED TIRES.
8. ELECTRICAL SYSTEM HOT WIRES MAY BE INSTALLED.
9. AIR CLEANER MUST BE IN PLACE.
10. BODY RULES
A) YOU MAY WELD AS MUCH AS YOU WANT IN FRONT OF, BUT NOT INCLUDING RADIATOR SUPPORT. YOU MAY NOT ADD ANY STEEL. NO LOADED OR HOMEMADE BUMPERS. INSIDES OF BUMPERS MUST BE VIEWABLE FOR INSPECTION. FRONT AND REAR BUMPER MAY BE WIRED OR CHAINED TO BODY IN 2 PLACES, NOT THE FRAME. BUMPER MAY BE CUT WITH TORCHES ONLY, NO SHARP EDGES. REAR BUMPER MAY HAVE NO MORE THAN 2” OF WELD AT EACH MOUNTING SIDE, TOTAL OF 4” OF WELD FOR BOTH SIDES.
B) YOU MAY REPLACE BODY BOLTS WITH 5/8” BOLT OR ALL THREAD WITH 3” WASHERS, NO THICKER THAN ¼”. RUBBER MOUNTS MUST BE IN PLACE. NO HOCKEY PUCKS, RUBBER MUST BE ORIGINAL.
C) HOOD MAY BE BOLTED DOWN WITH 5/8” BOLTS OR ALL THREAD AND 3” WASHERS NO THICKER THAN ¼” IN 4 PLACES. BOLTS OR ALL THREAD CAN BE A MAXIMUM OF 6” LONG AND NOT ATTACHED TO THE FRAME. WIRE OR CHAIN IS ACCEPTABLE.
D) DOORS AND TRUNK MAY HAVE 12” OF WELD ON EACH SEAM, 4” AT A TIME, MINIMUM 3” SPACE BETWEEN WELDS. WELDING MATERIAL MUST BE NO MORE THAN 2” WIDE AND 1/8” THICK. WIRE OR CHAIN IS ACCEPTABLE OPTION IN 4 PLACES.
E) WHEEL WELL MAY BE CUT FOR CLEARANCE AND REBOLTED IN 4 PLACES EACH.
F) HOOD AND TRUNK MUST HAVE A MINIMUM 12” X 12” HOLE. HOLE MAY BE REBOLTED IN 8 SPOTS. HOOD MUST COVER THE FAN.
G) THERE MUST BE A METAL STRAP, WIRE OR CHAIN FROM THE WINDSHIELD TO THE ROOF ON THE DRIVER’S SIDE.
H) REAR FRAMES MAY BE CUT OR DIMPLED ON 2 PLACES, EACH SIDE.
I) YOU MAY PREBEND REAR OF CAR, MAXIMUM 2”. OFFICIALS DECISION IF YOU HAVE OVER DONE IT.
J) NO WEDGING, DIMPLING OR FOLDING OF CARS.
K) TRUNK AND FLOOR PATCHES ARE ACCEPTABLE AND MUST BE THE SIZE OF THE HOLE ONLY. METAL MUST BE SAME THICKNESS AS OLD MATERIAL AND WELDED OR SCREWED 1” ON 1” OFF. PATCHES MUST BE PAINTED FLUORESCENT ORANGE.
11. DRIVE TRAIN
A) ANY MOTOR, TRANSMISSION OR 5 LUG REAR END MAY BE USED. PERCHES MAY BE MODIFIED TO FIT BUT CANNOT REINFORCE REAR END AT ALL. NO REAR END BRACING OF ANY KIND WILL BE ALLOWED.
B) MOTOR MAY BE WELDED IN AT MOUNTS.
C) TRANSMISSION MAY BE WELDED IN AT MOUNTS. CROSS MEMBERS MUST BE EITHER STOCK, OR YOU MAY USE A 2" DIAMETER BAR OR PIPE, WITH ONE PIECE OF C-CHANNEL WELDED TO EACH END. C-CHANNEL MUST BE NO LONGER THAN 6". YOU MUST BOLT IN ALL CROSS MEMBERS WITH NO MORE THAN 2 BOLTS PER SIDE. BOLTED TO FRAME ONLY.
D) DISTRIBUTOR PROTECTORS ARE ALLOWED. THERE MUST BE A MINIMUM 1” SPACE BETWEEN PROTECTOR AND FIREWALL.
E) PULLEY PROTECTORS AND ENGINE CRADLES ARE ACCEPTABLE. NO TRANSMISSION BRACES OF ANY KIND ALLOWED.
F) TRANSMISSION LINES MUST BE REMOVED FROM RADIATOR. TRANSMISSION COOLERS MUST BE UNDER THE HOOD.
G) SHIFTER MAY BE DIRECT TO THE TRANSMISSION.
H) ALL ANTIFREEZE MUST BE REMOVED.
I) EXHAUST MAY EXIT THROUGH THE HOOD.
J) ELECTRIC FAN, CLUTCH FAN OR PLASTIC FAN ONLY.
K) SLIDER DRIVE SHAFTS ARE PERMITTED.
L) WATTS LINK CONVERSION KITS ARE ACCEPTABLE.
12. SAFETY CAGE
A) FOUR POINT CAGE IS ALLOWED. IT MUST GO ACROSS DASH, BESIDE DOORS AND ACROSS BACK OF SEAT. BAR BEHIND SEAT CAN BE NO MORE THAN 6” BEHIND SEAT. IT MAY BE ATTACHED AT 4 CORNERS ONLY. METAL MUST BE NO LARGER THAN 4” DIAMETER. MUST BE WELDED AT CORNERS ONLY, DON’T OVER DO IT. SAFETY CAGE CANNOT BE ATTACHED TO FRAME AT ALL.
B) 2 UPRIGHT POSTS AND HALO BAR IS PERMISSIBLE, MAXIMUM 3” DIAMETER. HALO BAR MAY BE ATTACHED TO ROOF IN 2 PLACES.
C) NO GAS TANK PROTECTORS.
13. SUSPENSION
A) SPRINGS MUST BE ORIGINAL TO VEHICLE.
B) 2 CLAMPS PER SIDE ON LEAFS AND COILS.
C) YOU MAY CHAIN HUMPS TO REAR END.
D) YOU MAY STUFF OR WELD SHOCKS TO SET HEIGHT.
E) MAXIMUM BUMPER HEIGHT 20” TO BOTTOM.
F) FRONT SUSPENSION MUST REMAIN STOCK INCLUDING A ARMS, TIE RODS, TIE ROD ENDS AND BALL JOINTS.
G) YOU MAY BOLT OR CHAIN EACH A ARM IN 1 PLACE TO SET HEIGHT.
H) YOU MAY ADD 1 UNIVERSAL JOINT TO STEERING COLUMN IN PLACE OF RAG JOINT.
I) VEHICLES MUST HAVE ORIGINAL SUSPENSION CRADLES.
14. YOU MAY NOT BOLT, WELD OR WIRE ANYTHING ELSE, ANYWHERE ON THE CAR UNLESS IT SPECIFICALLY SAYS SO IN THE RULES. NO EXTRA BOLTS, FRAME OR SEAM WELDING.
15. TOP 5 CARS WILL BE RE-INSPECTED AFTER THE FEATURE FOR OFFICIAL DECISION.
16. THESE RULES ARE WRITTEN IN BLACK AND WHITE, THE GRAY AREA IS NOT A GOOD PLACE TO BE!
BUCKLE UP!!
IF YOU HAVE BUILD QUESTIONS CALL JIM AT 508-577-6850
ANY OTHER QUESTION CALL EILEEN AT 508-577-3451
|
|
