|
Post by weldnutj5 on Aug 10, 2014 22:12:05 GMT -5
So with 80s spindles will 15 ranger wheels fit with front brakes thanks for any info
|
|
|
Post by pdex982 on Aug 13, 2014 18:16:58 GMT -5
I would assume that an 80's steel one would just bolt right on. just measure the depth that rod goes in the masters if unsure. We figured the same so we bought one and tried and it won't even bolt to the booster. The hole in the booster is way bigger around too. Looks like we may have to go to manual brakes unless anyone knows of one that will work with the booster on the bubble. Thanks for the suggestion
|
|
|
Post by STROMI 121 on Aug 13, 2014 19:45:36 GMT -5
Why not just ditch the useless booster?
|
|
|
Post by redwreckincrew4 on Aug 14, 2014 0:12:56 GMT -5
Hey guys I am changing upper and lower a-arms and spindles on a 89 Vic with 75 caprice parts. Are there any know problems I am going to run into by doing this? I am changing because they were all pulled from car already. Thanks for help.
|
|
|
Post by STROMI 121 on Aug 15, 2014 21:34:18 GMT -5
You will loose ride/front bumper height.
|
|
|
Post by Krazy12 on Aug 20, 2014 13:35:07 GMT -5
Is there anyway to lift the front of a 92 Lincoln besides coil springs from a truck? It's for a bone stock show so no welding but I thought I'd ask
|
|
|
Post by moparpowered60 on Aug 20, 2014 13:57:41 GMT -5
Is there anyway to lift the front of a 92 Lincoln besides coil springs from a truck? It's for a bone stock show so no welding but I thought I'd ask We use the twist in coil spring spacers. Works pretty good. But they are a pain to put in.
|
|
|
Post by toad00t on Aug 31, 2014 21:56:31 GMT -5
This may be a dumb question but I have a factory mid 90 Vic and was curious if I would be able to use the steering column and cut the steering wheel off and out quick attach on it. It does telescope. If this is possible I will just use it for years to come. Any help would be great if there r easier ways or where to buy the parts
|
|
|
Post by oldtrx on Nov 9, 2014 20:38:18 GMT -5
I know it's possible to put 70's impala hubs on Vic spindles, was wondering if anyone knows if a 76 olds98 hubs will fit the same way. Also, is it the inner or outer bearing I have to swap to the Vic bearing to make it work.
|
|
|
Post by gassalazzz on Dec 11, 2014 16:43:39 GMT -5
I'm needing a little more front end height on a 1980 Lincoln. A - arms are welded down. Thanks
|
|
|
Post by Comet Cyclone on Dec 11, 2014 22:01:01 GMT -5
taller tires and or lower opposite end of car, or taller spindles....
|
|
|
Post by gassalazzz on Dec 12, 2014 10:36:30 GMT -5
I have 15s on the front and 14s on the back.
|
|
|
Post by redneckracing12 on Dec 12, 2014 11:25:04 GMT -5
Did you cut the bump stops out and the bump stop bracket off before welding the a arms down?
|
|
|
Post by gassalazzz on Dec 12, 2014 14:26:29 GMT -5
Did you cut the bump stops out and the bump stop bracket off before welding the a arms down? Could you get me a picture of what your talking about exactly. Took the rubber stop out and they aren't welded down yet. But will be doing soon if you could show me what your talking about. Thanks
|
|
02
Heat Winner
Official Keyboard Jocky, and Sh!t Starter!
Posts: 373
|
Post by 02 on Dec 12, 2014 16:06:09 GMT -5
There is a small metal bracket that the bump stop was in. It comes of the frame under the a arm. If you go look you will see it. Cut that off and you will gain a little height
|
|