|
Post by flip08 on Feb 22, 2013 16:53:56 GMT -5
|
|
|
Post by cb1187 on Mar 8, 2013 0:56:21 GMT -5
Winslows custom shop builds a upper motor mount to bolt to the block and it drops right into box ford lowers, the transmission I believe bolts to the stock ford crossmember also. They are like 40-45 a set. I have a pair of these and haven't had any troubles they are nicely built. he has a store in the vendors section
|
|
|
Post by derby111 on Mar 8, 2013 8:30:18 GMT -5
Winslows custom shop builds a upper motor mount to bolt to the block and it drops right into box ford lowers, the transmission I believe bolts to the stock ford crossmember also. They are like 40-45 a set. I have a pair of these and haven't had any troubles they are nicely built. he has a store in the vendors section i also ran a set of these this year great product!
|
|
|
Post by rottedframes on May 11, 2013 23:13:40 GMT -5
put my motor in and the front of the motor sit high and the tranny points down wards and my dumbass welded it in already before looking to see how it sat wht should I do
|
|
|
Post by BONESHAKER on May 11, 2013 23:35:17 GMT -5
um if you don't like the way it sits take a cutting wheel or grinder and cut the welds
|
|
|
Post by rottedframes on May 12, 2013 8:38:40 GMT -5
I did cut it out and set it back in last night and still sits the same way. im probably going to weld square tubing to the cross member to bring the tranny up some
|
|
cw09
Heat Winner
Posts: 528
|
Post by cw09 on May 12, 2013 22:39:13 GMT -5
Tilt it enough and the trans will be perfect.
|
|
|
Post by BONESHAKER on May 12, 2013 22:53:31 GMT -5
if you space the trans up you better check for clearance on your driveshaft. if it was be I wouldn't space the trans up but to each there own
|
|
|
Post by rottedframes on May 13, 2013 8:46:17 GMT -5
I don't wanna space the tranny either but im going to change rearend and put driveshaft in too see how it sits ill leave it how it is as long as my driveshaft doesn't bind up or at a weird ass angle and I also got it tilted far got 8 1/2 in spacers
|
|
|
Post by jugulator on May 13, 2013 19:44:08 GMT -5
put my motor in and the front of the motor sit high and the tranny points down wards and my dumbass welded it in already before looking to see how it sat wht should I do what mounts did you use ?
|
|
|
Post by rottedframes on May 13, 2013 22:54:55 GMT -5
they are box ford mounts
|
|
Jon
Heat Winner
Posts: 591
|
Post by Jon on May 14, 2013 9:17:49 GMT -5
do you have pictures of this would help decide if its a bad deal or if its all good
|
|
|
Post by flip08 on May 14, 2013 10:05:48 GMT -5
Buy the mounts on page 3. You can get them from me or on derbypars.com
|
|
|
Post by jugulator on May 14, 2013 10:51:12 GMT -5
don't use them.... too high,, use chevy mounts,,, or the chevy derby mounts mentioned here..
|
|
|
Post by rottedframes on May 14, 2013 11:48:41 GMT -5
heres a pic can get a better one today.. I was told it sat too high in the front because the pulley is above the sway bar
|
|