|
Post by I'll blow ur mind on Sept 30, 2018 16:53:03 GMT -5
Paulding County Fair June 9th 2019. Will be having a 3 man compact team show NO MAXIMUM on teams allowed to enter if we get more than 10 Teams we will run. Heats and feature entries will open Monday November 5th 2018 entry will be $200 per team and will include 2 pit passes to enter please email your information to Tobyhe86@gmail.com we will also be accepting PayPal payment for the entry fee please use the friend and family option and send it to the same email as your entry info
|
|
crazychris03
Heat Winner
Enter your message here...
Posts: 398
|
Post by crazychris03 on Oct 1, 2018 18:45:12 GMT -5
What about a big car team show
|
|
improse
Feature Winner
Posts: 1,203
|
Post by improse on Oct 5, 2018 0:02:01 GMT -5
Hope you guys rewrite your compact rules with good detail.
Rules below leave a lot open to the builder.
Compact Cars Rules • NO ENGINE PROTECTORS ALLOWED OR BEAD LOCKS 1. 108” maximum standard wheel base center to center, no alterations. 2. Factory gas tanks can stay in, if in front of rear axle. 3. Four point cage may not extend past the dash bar or more than 18” behind the driver’s seat. Gas tank protectors cannot be any wider than 24 inches and cannot extend past rear seat. 4. Maximum of a 5 lug rear end. 5. Bumper straps may be used to securely fasten a bumper on either end of the car. No homemade brackets. 6. Front bumper brackets, if there are not stock to the car they are one they cannot be any longer than 10” . If you run a bumper shock inside a frame it can only be 10 inches long and must have an inspection hole to verify where it stops! You cannot have brackets on the side of frame and a shock bracket inside of the frame. 7. No down bars off of cage. 8. Rear window bars may not be welded to trunk lid. If no trunk lid it must go straight down.
|
|
|
Post by Suck My Vic on Oct 6, 2018 7:49:33 GMT -5
Hope you guys rewrite your compact rules with good detail. Rules below leave a lot open to the builder. Compact Cars Rules • NO ENGINE PROTECTORS ALLOWED OR BEAD LOCKS 1. 108” maximum standard wheel base center to center, no alterations. 2. Factory gas tanks can stay in, if in front of rear axle. 3. Four point cage may not extend past the dash bar or more than 18” behind the driver’s seat. Gas tank protectors cannot be any wider than 24 inches and cannot extend past rear seat. 4. Maximum of a 5 lug rear end. 5. Bumper straps may be used to securely fasten a bumper on either end of the car. No homemade brackets. 6. Front bumper brackets, if there are not stock to the car they are one they cannot be any longer than 10” . If you run a bumper shock inside a frame it can only be 10 inches long and must have an inspection hole to verify where it stops! You cannot have brackets on the side of frame and a shock bracket inside of the frame. 7. No down bars off of cage. 8. Rear window bars may not be welded to trunk lid. If no trunk lid it must go straight down. Where are the rest of the rules? This can't be all of them?
|
|
|
Post by I'll blow ur mind on Oct 6, 2018 7:51:36 GMT -5
Hope you guys rewrite your compact rules with good detail. Rules below leave a lot open to the builder. Compact Cars Rules • NO ENGINE PROTECTORS ALLOWED OR BEAD LOCKS 1. 108” maximum standard wheel base center to center, no alterations. 2. Factory gas tanks can stay in, if in front of rear axle. 3. Four point cage may not extend past the dash bar or more than 18” behind the driver’s seat. Gas tank protectors cannot be any wider than 24 inches and cannot extend past rear seat. 4. Maximum of a 5 lug rear end. 5. Bumper straps may be used to securely fasten a bumper on either end of the car. No homemade brackets. 6. Front bumper brackets, if there are not stock to the car they are one they cannot be any longer than 10” . If you run a bumper shock inside a frame it can only be 10 inches long and must have an inspection hole to verify where it stops! You cannot have brackets on the side of frame and a shock bracket inside of the frame. 7. No down bars off of cage. 8. Rear window bars may not be welded to trunk lid. If no trunk lid it must go straight down. Where are the rest of the rules? This can't be all of them? These was last years rules
|
|
improse
Feature Winner
Posts: 1,203
|
Post by improse on Oct 6, 2018 20:09:10 GMT -5
Twisted Metal Demo Crew 2018 Rules ALL ENTRIES MUST BE IN INSPECTION LINE 1 HOUR PRIOR TO THE START OF THE DERBY OR AN ADDITIONAL $50.00 FEE WILL BE ADDED TO PARTICIPATE! Entry and Registration 1. Each driver must fill out an entry blank in its entirety. 2. Each driver and pit crew member must sign a release form prior to entering the pit area. All injuries must be reported to the officials at once. Only drivers, owners, mechanics, crew members that sign the release sheet will be allowed in the pit area. 3. Each driver must be 16 years of age or older and must hold a valid driver’s license. If under 18 years of age, the driver must have a notarized release signed by a parent or legal guardian. 4. If you are pregnant and/or have back, heart, or health problems, you are not permitted to compete. 5. Any driver or crew member not obeying the rules will be disqualified. Drivers are responsible for the actions of their crew members. 6. All competition rules are explained at the mandatory drivers meeting. 7. The track owners, fair board have the right to approve or reject any entry. 8. The track owners, fair board is not responsible for any vehicles, parts, or personal property at any time. 9. Any American made hardtop automobile or station wagon is permitted. No convertibles, jeeps, hearses, ambulances, or 4-wheel drive cars will be permitted. Inspection 1. Only the driver will be permitted with each entry into the inspection area. NO SPECTATORS PERMITTED. 2. Each entry will ONLY be permitted one additional attempt through the inspection area. Build your vehicles to the rules! NO REFUNDS will be awarded for illegal entries. 3. All entries will be required to open hoods in the inspection area 4. All entries must be inspected 1 hour prior to show time. If vehicle is not in inspection line 1 hour before show starts, a $50.00 fee will be added to participate. Safety 1. Remove ALL glass, fiberglass, headlights, taillights, trim, interior, trailer hitches, etc. Vehicles must be swept clean. No junk tires, wheels, metal parts, etc. allowed. 2. All rear seats and flooring decking must be removed. Any sharp or protruding fins must be cut off the vehicle. 3. Standard safety belts, Z-90 approved helmet, and eye protection (face shield or safety glasses) are required. Neck braces highly recommended. Fire retardant suits, clothing, or hood is recommended. No shorts or shirtless drivers will be permitted. 4. Exhaust (either zoomies or headers) must point away from fuel lines and headers must be straight in the air. 5. All hoods must have a square hole directly cut above the carb. All hood and deck lid latches must be removed. 6. Firewalls may not be totally removed. If holes are cut for clearance purposes, the holes must be covered by something fireproof. If patched with metal, the metal must not be thicker than 16 gauge. 7. No spray devises or cans permitted in the vehicle. 8. All vehicles must have dependable brakes at all times. 9. Stock gas tanks must be removed from the original position. A replacement tank must be securely fastened in the rear section (no farther forward than the back of the front seat) of the drivers compartment. Steel gas tanks or Neoprene construction approved tanks may be used. No original tanks permitted. Gas tank must be securely fastened by means other than ratchet straps or wire. Tanks must be securely bolted to the floor. Tanks must be covered in a fireproof fashion. Any vehicle that spills gas will be disqualified immediately. Gas tank protectors maybe used must have a gap between the rear deck. 10. Electric fuel pumps are permitted, but the switch must be CLEARLY marked ON/OFF. 11. Stock batteries must be removed from the original position. A battery must located in the driver’s compartment and securely fastened to the floor. The battery must be covered. 12. No profanity will be permitted on any vehicle. MILD WELD • FOLLOW 2018 Bash Rules with the addition of all old iron including 1964-1966 imperials. Rules will be posted midNovember. Compact Cars Rules • NO ENGINE PROTECTORS ALLOWED OR BEAD LOCKS 1. 108” maximum standard wheel base center to center, no alterations. 2. Factory gas tanks can stay in, if in front of rear axle. 3. Four point cage may not extend past the dash bar or more than 18” behind the driver’s seat. Gas tank protectors cannot be any wider than 24 inches and cannot extend past rear seat. 4. Maximum of a 5 lug rear end. 5. Bumper straps may be used to securely fasten a bumper on either end of the car. No homemade brackets. 6. Front bumper brackets, if there are not stock to the car they are one they cannot be any longer than 10” . If you run a bumper shock inside a frame it can only be 10 inches long and must have an inspection hole to verify where it stops! You cannot have brackets on the side of frame and a shock bracket inside of the frame. 7. No down bars off of cage. 8. Rear window bars may not be welded to trunk lid. If no trunk lid it must go straight down. Full size Truck Rules • NO STRAIGHT FRAME TRUCKS (“STATE FRAME”) ABSOLUTELY WILL NOT RUN! 1. Any American made truck is permitted. 4-wheel drive trucks may only run 2WD (pull a driveshaft). Any STANDARD ONE TON and down is permitted. If truck frame has extra support brackets or is beefed up from the factory you better call before building and we’ll come look at it! Officials decision will determine if it can be ran!! Suburban’s are permitted. 2. Tailgates may be welded shut using 3”x¼” strap. A maximum of 48” of strap may be used. Back bumper or tailgate has to be 16” of the ground. 3. Beds must be welded to the cab of the truck with a 3” strap directly behind the doors. 4. An interior four point cage is required to compete. The cage may not extend outside of the cab into the bed. However, it may attach vertically to the frame in four locations. No metal may be added to the frame to attach the cage. The vertical bars must be welded directly to the frame. 5. Car bumpers may be used. Factory bumper brackets can be used or 3”x3” angle or square tubing 8” long. 6. A single piece of 3”x3”x¼” angle iron may be welded from the left front frame rail to the right front frame rail (in front of aarms) on all front coil sprung trucks only. Front leaf sprung trucks may use a chain from rail to rail or from the engine cradle to each rail. 7. Trucks must securely fasten gas tanks directly behind the center of the cab in the bed. 8. 48” piece of ¼”x2”x2” angle may be welded on inside of tailgate. 9. fix aplate rule 6”x6”x1/4” follow car rules! If abused plate will be cut off!!!! 10. NO HUMP PLATES 11. C-channel front frame trucks can run kickers off the front bar to the middle to the A arms no bigger than 2”x2” square tube. Boxed framed trucks down bars have to stop at firewall. 80’s & Newer Stock rules 1. Any STOCK American made 1980 or newer hardtop may be used. 2003 and newer Ford Motor Company full size cars, Crown Vic, Interceptor, Grand Marquis allowed MUST HAVE ORIGINAL FACTORY FRONT CRADLE, FRONT SUSPENSION AND STEERING. 2. Engine may be swapped (Chevy to Ford, Ford to Chevy etc.). HAS TO HAVE STOCK RUBBER MOUNTS. No engine cradles or distributor protectors. Weld or wire engine and transmission mounts in. 3. Hoods may be wired in six locations. 2 strands of 9 wire per hole. Sheet metal to sheet metal 2 spots to frame or bumper. Hoods MUST be open for inspection. Front and rear fenders may be trimmed for clearance. No bolting or welding inner fender to outer fender. 4. Drivers door only may be welded solid. All other doors can be welded shut with 2 3”x6” per door seam OR 6 locations per side 2 strands of 9 wire per hole not both. Sheet metal to sheet metal. 5. Trunks and tailgates may be wired shut in 6 locations or welded 6 places 3”x3” plates. Must have inspection hole if welded. 2 strands of 9 wire per hole and sheet metal to sheet metal 2 spots can go to frame or bumper. 6. NO WEDGING, TUCKING, SMASHING, COLD BENDING, TILTING OR PINNING OF QUARTERS OR BODY. Body must be stock appearing. Quarters maybe cut for wheel clearance 7. NO extra body mounts. MUST have stock rubber mounts, spacing and can add 4inch body spacers at core support. No bigger than 5/8” all thread can run through core support. 8. NO frame modifications, I.e. NO RESTUBBING. Frame must be STOCK. 9. Front Bumper may be swapped for any factory car bumper. Must have stock bumper mounts and may be welded to the mounts only. No extra metal may be added. 10. ALL suspension parts MUST be stock. May weld or wire in the rear coils. 11. May change body mount bolts. To a max ½” bolt with a max 3” washer. 12. 5 lug rear end only. 13. Frames may be notched BUT NOT welded back together. Engine 1. Full engine cradles, distributor protectors, header protectors, carburetor protectors, front/mid-engine plates, etc… are not permitted 2. Lower engine cradle is permitted for mounting purposes only! May not reinforce or strengthen the car in any way! 3. Engine swaps are permitted must be mounted to factory K-member/cradle only 4. Stacks/headers are permitted. Engine may be welded or chained to K-member only not to frame!! Transmission 1. Aftermarket shifters and slider shafts ARE permitted! 2. Trans protectors, braces, aftermarket bellhousing, and tail shafts are NOT permitted!! Frame-Suspension 1. MUST BE 100% STOCK! Tilting, cold bending, reshaping, of frame is NOT permitted!!!! 2 .2003 and newer fords are permitted, must have factory cradle steering and suspension!!! 3. Front suspension may be welded. If welded a maximum 2”x2”x1/4”plate is allowed on front and rear of upper a-arms bottom a-arms may NOT BE WELDED! 4. Must run factory front suspension components. No aftermarket or reinforced ball joints or spindles. 5. You may cut/notch/dimple the rear frame to help roll. Notched areas may NOT BE REWELDED!!! 6. Frames may NOT be shortened, front or rear!!! 7.Rear suspension may NOT be soild. No all-thread shocks. Must bounce! 8.Hump plates are NOT permitted. A chain or two strains of wire may be attached between the humps to prevent rear frame from hitting the tires. 9. Rear frame and bumper height must be at least 15” 10. Front sway bars may only be attached using factory brackets and mounts.NO WELDING! Tires 1. Any air filled tires are permitted. 2. Stock wheels only. Full wheel centers, wheel protectors, bead protectors, bead locks are not permitted! Electrical and Battery 1 .only one battery allowed must be securely fastened and covered before inspection. FIX-IT-PLATES!!!! 1 .Must have visible and significant damage! 2. May use 2 fix it plates per side PLATES NO LARGER THAN 4”X4”X1/8” and may only be welded on 3 sides of plate. 3. If size or thickness is abused it WILL be cut completely OFF!!! Rear-end 1. Any factory 5-lug automotive/passenger car rear-end housing is permitted. 2. Rear-end braces, and housing reinforcement is not permitted. Spider gears may be welded. Drivers Compartment 1. May have a 4 point cage around drivers compartment for safety. Maximum material dimension is 3” bar, square tube, channel, ect… One bar may be located behind the driver’s seat, across dash, and two connecting bars along driver and passenger doors. 2. The bar behind the seat can sit no further back than 6” past front door post. 3. A roll over bar is permitted May not be attached to the floor or frame 4. The cage bars may be attached to sheet metal only with a maximum 12”x12”x1/4”plate.Cage may NOT attach to frame. If the cage bars are not weld securely, they must be removed for your safety! 5. A gas tank “holder” is permitted. Holders may attach to floor or cage. If attached to cage, the holder may be up to 24” wide and must be 5” away from ALL sheet metal on all car. This rule will be strictly enforced. If less than 5” gap the holder will be removed.. MUST RUN ALL FACTORY STEERING, HOWEVER YOU CAN RUN AFTER MARKET COLUMN. YOU CAN ADD ONLY HAVE 2 KNUCKLES! NO AFTERMARKET GAS PETALS,BRAKE PETALS!NO TRANNY COOLERS INSIDE DRIVERS COMPARTMENT!DO NOT FOLLOW REGULAR CAR RULES THESE ARE THE STOCK RULES IF IT DON’T SAY YOU CAN DO IT THAN DON’T DO IT!!!!!!!!!!!! Youth This class is for the kids AGES 11-16. Bring Birth Certificate in case of a challenge of age. To let them learn to strip cars out and build a car to the rules and sportsmanship win or lose. Upon arrival a notarized parent and/ or legal guardian consent form must be filled out or you will not be allowed to participate. A parent and/ or legal guardian must ride with the driver. This is for instructional purpose as well as a possibly emergency situation. 1. A factory 4 or 6 cylinder front wheel drive only. 108” wheel base max. 2. Both front doors must be painted white. 3. Hoods may be wired in six locations. 2 strands of 9 wire per hole. Sheet metal to sheet metal NO frame or bumper. Hoods MUST be open for inspection. Front and rear fenders may be trimmed for clearance. No bolting or welding inner fender to outer fender or rolling fenders. 4. Drivers and passenger doors can be welded solid. Drivers and Passenger’s front door MUST have a bar or reinforcement on outside of doors, must stop at front doors. All other doors can be welded shut with 2 3”x3” plates OR 6 locations per side 2 strands of 9 wire per hole not both Sheet metal to sheet metal. 5. Trunks and tailgates may be wired shut in 6 locations. 2 strands of 9 wire per hole and sheet metal to sheet metal. Hoods MUST be open for inspection. Trunks can have 45” of weld. 6. May weld or wire in the rear coils. 7. Two locations of wire or rod must be placed from front cowl to the front of the roof to prevent hood entry into the driver’s compartment. 8. Stock batteries must be removed from the original position. A battery must located in the driver’s compartment behind the front seat and securely fastened to the floor. The battery must be covered. LAWN MOWERS RULES AND REGULATIONS 1. The garden or lawnmower must have a factory frame, no homemade frames. 2. Must be a front engine mower, no rear engines allowed. 3. All mowers must have factory stock engines. 4. Transaxles must be factory; reinforcing or spider gears is allowed. 5. Reinforcing the frame is permitted. 6. reinforcing around engine is allowed, but cannot be outside of the hood. 7. Hoods must remain factory. Hoods can be screwed down or welded. If hood is fiberglass, you can make a hood from sheet metal, but it is not allowed to be any bigger than the fiberglass hood was. 8. Brakes must be in operation when pulling in for heat race, must also have forward and reverse gear. 9. Gas tank must be fastened with cap on, if it comes loose or gas leaks you will be disqualified. 10. Some sort of leg guard is mandatory before entering arena, must go from rear fender to front foot rest or frame, and must be of 1-2 inch diameter. 11. The front of the frame under grill may be strengthened for hitting but must be a smooth finish, no front bumpers allowed. 12. A rear bumper is recommended, but not mandatory. It cannot extend 4 inches out from rear of mower. Some sort of back protection is recommended, but not mandatory. 13. Pulleys can be changed to increase speed. 14. Drivetrain modifications are allowed to change gearing but must stay original. (belt drive stays belt drive, chain drive stays chain drive) 15. Wheels must have factory rims with no modifications, tires of choice. No dual wheels or cut tires. 16. Mower decks must be taken off before entering pits, plus all headlights and any other plastics must be removed before entering pit area. 17. NUMBER MUST BE SOMEWHERE ON EACH SIDE OF MOWER. NUMBER MAY BE ON HELMET ALSO. 18. If mower does not pass inspection, or participant refuses to fix something, there will be no refunds. 19. Officials have final say, we reserve the right to check mower after the derby. 20. Driver must wear helmet, pants, long sleeve shirt, and eye protection when entering the track and during the derby. 21. No direct hits to the driver’s area. 22. If you are rolled over, the heat will be stopped and your lawnmower will be placed back on its wheels and you will be eliminated. 23. During the competition you must initiate contact within two (1) minutes. If at any time you cannot make contact within the time limit you will be disqualified 24. All motion to be halted upon signal from referees in case fire, injury, and other emergencies. 25. No hits when opponent is out of bounds. 26. No pit racing. 27. Drivers will inspect each other’s mowers before the driver’s meeting and will bring up any concerns after the meeting with the officials. Figure 8 race 1. Each driver must fill out an entry blank. All drivers must supply their own cars, only one entry per person. 2. Each driver must be 16 yrs old or must hold a valid driver’s license and have a notarized release signed by parent. 3. If you are pregnant, have back problems, and /or heart problems you are not allowed to run!! 4. The track owners or promoter reserves the right to approve or reject any entry. 5. Only owners, drivers, mechanics, etc. who sign the release sheet will be permitted in the pit area. Drivers only on the track. 6. The promoter, track owner or fair association will not be held responsible for any cars, parts, or personal property before, during and after show. Each car must be signed in and inspected at the track at least 1 hour prior to show time. Only 1 RE- INSPECTION PERMITTED!! If you do not pass the 2nd time, you will be disqualified with No Entry Re- imbursement. Official’s discretion will be used!! - PREPARATION OF CAR – 1. SAFETY IS A MUST!! 2. Remove all trim, emblems, plastic and glass (windows, lights, etc…) Sweep the car out from debris, BEFORE INSPECTION!! 3. Any sharp protruding fins or dangerous objects (smash down or cut off). 4. Chrome molding strips and bottom portion of back seats must be removed. BUMPERS: 5. Bumpers may be flipped over. 6. No trailer hitches 7. Cutting bumpers ends (fenders) for wheel clearance is allowed. 8. Bumpers can be loaded. DOORS: 9. It is recommended that the Driver’s door be painted White. A roof sign/number is allowed. IT MAY NOT REINFORCE ANY PART OF CAR!! 10. It is recommended the driver’s door be reinforced with steel bar, angle iron or pipe. 11. A strong wire or mesh screen is recommended on driver’s window & windshield area. Chain, wire or metal bar is STRONGLY recommended from driver’s door to roof 12. All doors are recommended to be fastened shut by wire, straps, chained or welded (steel no bigger than 3” in width and 1/8” thick) nothing to frame! NO OVER LAPPING!! Note: any metal wider or thicker is ILLEGAL and will be removed!! 3 or 4 – POINT CAGE & ROLL OVER BAR: 13. A 3 or 4 point cage is recommended for DRIVER SAFETY. BATTERY & GAS TANKS: 14. NO Alcohol motors 15. Stock gas tanks MUST be removed from the original position!! Replacement tank must be placed in the back seat area; all tanks must be securely fastened to floor and covered; a portable tank is recommended in place of the original. Gas tanks and fuel lines must be completely covered before inspection. Rubber hose inside car. Steel gas tanks or Neoprene Construction approved tanks can be used. 16. Only ONE battery, any size, is allowed. It MUST be securely fastened and COMPLETELY covered. NO MILK CRATES ALLOWED!! HOOD & ENGINE COMPARTMENT: 17. No spray devises or cans allowed in cars. 18. Exhaust stacks/ headers must point directly upwards!! 19. Firewalls may not be totally removed. If altered, the hole must be covered with something fire proof. This is for YOUR protection!! 20. Radiators, transmissions coolers and heaters must remain in original position or in engine compartment. In front of firewall. Radiator overflow hose must point STRAIGHT DOWN!! 21. Homemade radiators are allowed. 22. Carburetor must have some sort of cover/air cleaner attached to it!! 23. DOUBLE TIRES are allowed!! NO liquids, concrete or other material in tires permitted. No studs or screws in rims. No studs in tires. 24. No metal may cover or protect tires. No bead-locks. Valve stem protectors are ok. - RUNNING - A. Seat belt or Safety belt, Z-90 approved helmet (full face recommended) GOGGLES OR FACE SHIELD ARE REQUIRED. B. Neck braces are highly recommended!! C. Fire retardant suits, clothing or hood is recommended for personal safety. (NO shorts and must wear shirt) D. NO deliberate head-on collisions and NO deliberate hitting in driver's door. E. Vehicles must have dependable brakes at all times and Boundaries observed. F. NO alcohol or drugs on track or in the PIT area. ANYONE under the influence of alcohol or drugs will be immediately disqualified. G. No cars are permitted in the competition area before the heat in which they are to participate. H. A vehicle will be disqualified if the driver’s door comes open during the heat, or catches fire. I. A $100.00 Protest fee is required to contest another car. If you are a driver, you must give the head track official $100 cash! You then must state what car is illegal and where it is illegal. If you are right you WILL get your $100 back, if you are wrong, you will forfeit that $100. Derby officials reserve the right to inspect any car at any time!! J. Any vehicle visibly leaking fuel will be disqualified! K. Fire extinguisher is recommended at close reach in driver's compartment. L. Any driver or crewmember disobeying the rules will cause his or her car to be disqualified. Unsportsmanlike conduct will not be tolerated and will be grounds for disqualification and barring from future derbies. M. DRIVERS ARE RESPONSIBLE FOR THE ACTIONS OF THEIR CREW MEMBERS. N. FINAL WINNERS MAY BE INSPECTED. O. THE DECISION OF THE DERBY OFFICIALS WILL BE FINAL!! - RULE BOOK DISCLAIMER - The rules and/or regulations set forth herein are designed to prove for the orderly conduct of racing events and to establish minimum acceptable requirements for such events. These rules shall serve the conditions of all events, and by participating in these events, all participants are deemed to have complied with these rules. NO EXPRESSED OR IMPLIED WARRANTY OF SAFETY SHALL RESULT FROM PUBLICATION OF OR COMPLIANCE WITH THESE RULES AND REGULATIONS. They are intended as a guide for the conduct of the sports and are in no way a guarantee against injury or death to a participant, spectator, or official. The race director shall be empowered to permit minor deviation from any of the specification herein or impose any further restrictions that in his opinion do not alter the minimum acceptance requirements. NO EXPRESSED OR IMPLIED WARRANTY OF SAFETY SHALL RESULT FROM SUCH ALTERATION OR SPECIFICATIONS. Any interpretation or deviation of these rules is left to the discretion of the officials and the Fair Boards Power Wheels This class is for the kids AGES 4-10. Bring Birth Certificate in case of a challenge of age. Upon arrival a notarized parent and/ or legal guardian consent form must be filled out or you will not be allowed to participate. This is a Fun Class to get small kids their first taste, of a Derby, any Power wheels that are too fast or heavy will not be allowed to run. This is for the Kids to have Fun! 1. Power Wheels for Kids 4 years old and up. 3. Stock, Electric, Regular Size, Power Wheels with up to a 12 volt lawn mower battery. Battery can not be mounted in the passenger seat. 4. Helmets must be worn. 5. All doors, hoods, and tailgates must be strapped shut. 6. Use zip ties or duct tape to fasten shut doors, hood, and trunk. No sharp or protruding edges. Track official and or inspectors decisions are final. Ryan Tittle 419-618-8785, Jayvid Opp 567-207-4090, Joey Bowman 419-937-3568.
|
|
improse
Feature Winner
Posts: 1,203
|
Post by improse on Oct 6, 2018 20:27:24 GMT -5
3 of us are thinking of running the 3 man team show come next June. Between 2 of us we have dam near 65 years of building cars/wrecking cars. I take it v8's,seam welding of entire car/frame, loaded/frame bumpers ect will pass inspection ?? I do not want to spend all winter building for the June 2019 team event and show up with 3 compacts built to hell and not pass inspection.
Trust me not trying to start no crap/piss ya off, just want to make sure our builds are equal to others is all.
|
|
Vito324
Feature Winner
For badass roof signs, Check out BlackFlag Designs on Facebook!
Posts: 2,189
|
Post by Vito324 on Oct 10, 2018 7:13:49 GMT -5
76-81 Camaro or a 80-85 GM G Body would be the cars I choose for that rule package. If they don’t do anything to those rules it’ll definitely be a load fest..
|
|
|
Post by I'll blow ur mind on Oct 10, 2018 7:18:30 GMT -5
76-81 Camaro or a 80-85 GM G Body would be the cars I choose for that rule package. If they don’t do anything to those rules it’ll definitely be a load fest.. I was thinking fox body mustang or pacer or germlin with a Sbc or 4.3
|
|
Vito324
Feature Winner
For badass roof signs, Check out BlackFlag Designs on Facebook!
Posts: 2,189
|
Post by Vito324 on Oct 10, 2018 7:19:59 GMT -5
76-81 Camaro or a 80-85 GM G Body would be the cars I choose for that rule package. If they don’t do anything to those rules it’ll definitely be a load fest.. I was thinking fox body mustang or pacer or germlin with a Sbc or 4.3 Or an AMC Eagle. Should be a decent show.
|
|
|
Post by I'll blow ur mind on Oct 10, 2018 7:21:05 GMT -5
I was thinking fox body mustang or pacer or germlin with a Sbc or 4.3 Or an AMC Eagle. Should be a decent show. Vito get u one I got a 4.3 I’ll sell u to put in one
|
|
Vito324
Feature Winner
For badass roof signs, Check out BlackFlag Designs on Facebook!
Posts: 2,189
|
Post by Vito324 on Oct 10, 2018 7:33:07 GMT -5
Or an AMC Eagle. Should be a decent show. Vito get u one I got a 4.3 I’ll sell u to put in one I’m done with Compacts lol.
|
|
|
Post by I'll blow ur mind on Oct 10, 2018 8:00:38 GMT -5
Vito get u one I got a 4.3 I’ll sell u to put in one I’m done with Compacts lol. Come on put a team together
|
|
|
Post by I'll blow ur mind on Oct 10, 2018 8:01:16 GMT -5
Vito get u one I got a 4.3 I’ll sell u to put in one I’m done with Compacts lol. I’m sure Jon and Chris will be running this show
|
|
|
Post by ADDICTEDtoIMPACT on Oct 20, 2018 20:43:49 GMT -5
So this is a mid-size car team show not compacts from what I am reading?
|
|